Question about Peugeot 407

Open Question

Where is the ECU for the front parking sensors located in the two door 2006 Peugeot 407 Coupe

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: need to change rear pads and adjust hand brake on a 407

right the hnad brake is located on the center console at the right of you in america or left if you are are from brittan. pull it=]

Posted on Jun 26, 2008

Ad
  • 1244 Answers

SOURCE: Peugeot 407 not 405 blocked windscreen washer

its in the pump it self mate ya have to take the pummp out of the bottle

Posted on Jan 17, 2010

  • 1 Answer

SOURCE: Peugeot 406 Coupe v6 . Speedometer Problem

i had the same problem, in behind the glove box there is a black cigarette sized box, this was faults on my 406 coupe and the speedo didn't owrk, or suddenly it shot from 0 while dribing up to 30 or what ever my speed was, it also wrecked my powersteering rack trying to drive it, as it made terrible noises as its speed sensitive. you local peugeot dealer will be able ot get you one. i can't remember how much it cost, sorry.

Posted on Feb 16, 2010

Raysagem
  • 1017 Answers

SOURCE: Peugeot 407 SW 2006 wash wipe, no water coming from front.

The pipe that caries the water come off the connector under the wheel arch, you have to take the wheel off on the side of the water reservoir and the protective lining. Apply a bit of super glue to it, it's not very difficult to do.

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: how do you remove inner front door panel from

This is not a complete solution but hope it helps.
Their are 2 screws on the side of the door, as well as their is a screw on the control panel under the little mat, all those have to go befor u try anything else


Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Solenoid rattle on start up. Goes away immediately on start. V 6 motor


peugeot 407 v6 3.0 very short-time rattling(grinding) noise at ...

? 0:13
https://www.youtube.com/watch?v=ZRJzci7qvNA
Feb 27, 2012 - Uploaded by reza679
peugeot 407 v6 3.0 very short-time rattling(grinding) noise at cold-start, source ... but a friend told me it can be anything else as well (like those solenoids)! ... C6 makes when starting cold - is that a VVT or a valve lifter noise?.

407 [Archive] - Peugeot Forums

www.peugeotforums.com > Peugeot Forums > Peugeot Models
Mar 22, 2011 - Key replacement · Wishbones for 407 · ESP/ASR Faulty · RT4 VIN coding · 407 1.6 2004, Crankshaft pulley.. size, part number.. 407 driver door lock replacement ... Peugeotforums.com Suggestions and Help [Archive ...
Mar 24, 2011
General Discussion [Archive] - Page 4
Mar 21, 2011
More results from www.peugeotforums.com

Jan 26, 2016 | 2006 Peugeot 407 1.6

1 Answer

I have a 407 Peugeot Coupe V6 HDI Diesel faulty code P1351 it says IDM Input circuit malfunction/ Ignition coil control circuit high voltage and what must i do to solve the problem


Must be some bad information getting to the ecu. Bad conections due to salt corrosion may be the cause. Bright metal contacts are essential for correct transmission of information from sensors to and from the ECU (brain).

Apr 14, 2015 | Peugeot Cars & Trucks

1 Answer

2006 Peugeot wont come out of park, PRND is on dash.help


hi, ham sorry for late, prnd this massage come form gearbox check gear pressure's

Mar 04, 2015 | 2006 Peugeot 407 1.6

1 Answer

2006 peugeot 407 3.0 v6 firing order & cylinder lay out.


163524 no 1 acording to my alldata book is front of engine on the right ,rather standing in front of car its on the right and numbers 1to3 right to left rear bank is again right to left 456 .hope this helps

Jan 30, 2013 | 2005 Peugeot 407 3.0

2 Answers

Prnd


It is not a (Alarm) Those letters Are for what gear you put the car into. P means (Park) R means (Reverse) N means (Nuetal) D means (Drive)

Oct 23, 2012 | 2006 Peugeot 407 1.6

1 Answer

Peugeot 407 coupe 2.7 hdi p0069 fault code comes up depollution system faulty


o2 sensor needs to be replaced and computer reset by disconnecting battery negative cable for 1/2 hr then reconnecting. Good Luck!

Oct 20, 2011 | 2005 Peugeot 405

2 Answers

Peugeot 407 05 reg my abs and esp lights stay on why


have it plugged in at your local garage and if it comes up with right rear wheel speed sensor faulty then dont panic!!
usually if you remove the sensor and clean up the area where it sits with some sand paper or a file and re fit it then it should be fine

let me know if this helps
cheers

Oct 12, 2010 | 2006 Peugeot 405

1 Answer

Peugeot 407 SW 2006 wash wipe, no water coming from front.


The pipe that caries the water come off the connector under the wheel arch, you have to take the wheel off on the side of the water reservoir and the protective lining. Apply a bit of super glue to it, it's not very difficult to do.

Feb 21, 2010 | 2006 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...