Question about Cars & Trucks

1 Answer

93 cherokee 4.0 crank shaft sensor location - Cars & Trucks

Posted by Anonymous on

  • Bill George
    Bill George Apr 18, 2017

    It is toward the top of the transmission and id where the engine and transmission bolt together.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,372 Answers

If i remember correctly it is on the drivers side and is bolted on the transmission with 2 bolts.

Posted on Apr 18, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank shaft sensor for a 93 mercury sable


The 3.0 engine should be near the crank pulley in front of the engine.
The 3.8 engine uses a distributor.

Apr 14, 2013 | 1993 Mercury Sable

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand cherokee


CRANKSHAFT POSITION SENSOR LOCATION FOR 4.0L ENGINE IS ON TRANSMISSION BELLHOUSING AT THE LEFT REAR OF THE ENGINE. FOR 5.2L ENGINE CRANKSHAFT SENSOR LOCATED ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand Cherokee


If your stateside the CPS is on the drivers side of the bell housing at approx 11 oclock.They have 1 or 2 bolts securing them.assuming its the 4 litre motor.If its right hand drive the CPS is on the fornt seat passengers side.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Locate crank shaft sensor on 1998 jeep grand cherokee


4.7L ENGINE CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK ABOVE THE STARTER. ON THE 4.0L ENGINE CRANKSHAFT SENSOR LOCATED TRANSMISSION BELL HOUSING AT THE LEFT REAR OF THE ENGINE. THE 5.2L 5.9L CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Nov 26, 2010 | 1998 Jeep Grand Cherokee

1 Answer

I own a 2002 Jeep Cherokee. Where is the oxygen sensor bank 2 sensor 2 located. This jeep has 4 oxygen sensors. Thanks


the bank 1 and 2 refer to what side of the car ir is on. Bank 1 is passenger side bank 2 is drivers side sensor 1 and 2 refer to before and after the catalytic. sensor 1 is before and 2 is after . i hope this helps and just a references if your cam shaft sensor and crank shaft sensor have not gone bad yet i would have them checked. usually these go bad really quick on jeeps. just had to replace both my cam and crank sensors and with out labor it cost around 100 with labor about 150 to 200. and the o2 sensors run anywhere from about 50 to 150 depends on the quality you want

Nov 03, 2010 | 2002 Jeep Grand Cherokee

1 Answer

93 jeep Cherokee wont start


Could be a crank or cam sensor gone bad. I suggest you get a haynes or chilton manual and do the testing outlined in them to determine which it is. Neither item is very inexpensive and the crank sensor is a real pain to replace. There are other things that can do that so testing is important.
Crank sensor is the most common failure but asd relay, wiring problems, bad ground on a relay etc can do much the same thing.
Anything you find that you need further help with I'll be happy to answer if I can!
Good Luck!

Apr 17, 2010 | 1993 Jeep Grand Cherokee

2 Answers

2001 jeep cherokee cranks but wont start and has


If all the fuses are good,replace the crank shaft sensor,this is the problem.

Jan 04, 2010 | 2001 Jeep Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

2 Answers

Where is the crank senser located on a 93 jeep cherokee 6 cylinder


On the back of the engine, under the firewall, driver side. You can barely see it from above. You have to change it from underneath.

Jun 25, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...