Question about Cars & Trucks

Open Question

Looking to install front left headlamp on a 2010 Coachman Mirada having problem taking the old one out, AJ

I want to replace the old headlamp in old a have a new one

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: replacing headlamps

you shouldnt have to

Posted on Aug 30, 2008

  • 11 Answers

SOURCE: Replacing my headlamps on my 96 Chevy Tahoe

On a 99 Tahoe Don't remove the grill.. There are two 6 inch long, hex head, vertical screws protruding from the frame above the headlight. To unscrew use a small hex socket.. maybe 1/4 inch. Turn the screws counterclockwise to remove till loose then pull up. The screws serve as a linch pin to secure the headlight to the mounting bracket. Here's a pic of the driver side light. Also, I had very good results with my park light lenses in 5 minutes with a hand drill, a soft buffing pad, and some fine polish. They were yellow and dull and looked clear and white when done. I washed the inside of the lense with soapy water and a soft toothbrush.. it made a big difference.fcb90cc.jpg

Posted on Apr 07, 2009

  • 1986 Answers

SOURCE: no power to left front headlamp - low beam

There are relays that control the headlights in a fuse box under the hood near the firewall.. There's also a fuse box underneath the dash on the driver's side, but can't remember if it's on the underside of the dash or beside it

Posted on Aug 12, 2009

abauto
  • 353 Answers

SOURCE: wanting to install or replace HEADLAMP on a saab

Bumper does not need to be removed but it does need to be disconnected and pulled out to give sufficient room for the headlamp to be removed.

Posted on Nov 25, 2009

youredone82
  • 426 Answers

SOURCE: left turn signal doesn't work

is this the left side front that is the only light that will not light?

Posted on Dec 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 325i 2010 has lost all power and I can't get into the boot to check the battery. Any ideas?


Open the bonnet and look for a red cap with a positive sign on usually to the left if looking from the front, this is for the battery and just behind the drivers headlamp is a silver bolt which is the negative. You can put jump leads on them and you will be able to open Boot to charge battery or charge from that point.

Feb 28, 2017 | Cars & Trucks

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

1 Answer

How do I replace the headlight assembly MN133516


The 2003 Outlander utilizes replaceable (9007) headlight bulbs. If you're looking to replace the bulb(s);
1. Raise the hood.
2. Remove the plastic cover at the rear of the headlamp assembly by rotating it counterclockwise, and pulling it off. This will allow access to the headlight bulb.
3. Twist the bulb socket counterclockwise in order to remove it from the headlamp assembly. Pull the old bulb out of the socket, and use a clean cloth to install the replacement bulb. Do not touch the glass of the new bulb.
4. Place the socket back into the assembly, and twist it clockwise. Reattach the plastic cover, and close the hood.
Are you needing DIY instructions for replacing the entire headlamp assembly? Left (driver) or Right (passenger)?

Jan 18, 2013 | 2003 Mitsubishi Outlander

1 Answer

I own a new German Registered Range Rover SC and would like to take it to the UK. How does one adjust the headlamp beam for left hand drvining?


The auto headlamps can be adjusted in the menu. with vehicle running press the down arrow on the right side control button at the top right steering whell control
menu options will now show on the screen between speedo and tach, scroll to vehicle setup then to headlamp assist then creen comes up high beam assist on, drive on left and drive on right, select drive on left.

Nov 22, 2010 | 2010 Land Rover Range Rover

1 Answer

Changing Low Beam Headlamp Replacement 2005 Mazda 3.


Check out the following:
It's not easy. You need a flashlight. First, take the batter vent assembly off by removing the screw over the headlamp assembly. Open the battery box by snapping off the tabs, lift out, and move the vent to the side. Second, disconnect the headlight wire by pressing down on the opposing tabs located on the side of the connector and pull straight back. Move the wire to the side. Next, peel the rubber fitting around the bulb (located on the back of the headlamp assembly). Look inside the headlamp assembly with a flashlight to see what you got yourself into. You'll have to unhook the retainer wire that holds the bulb in place. This requires you to push the top part of the wire toward the front of the car and lift up. The wire should swing to the left (passenger side) releasing the bulb and bulb housing. Pull the old bulb out of the housing (it might be tight), replace with the new one (try not to touch the glass). Replace the bulb/housing. Make sure the little tap fits back into its slot (upper diver side). Push the wire clamp back over the bulb, pushing up back and down making sure it's hooked and your done. It seems easy once you've done it.
Good luck! EJ Kudelka

Nov 09, 2010 | 2005 Mazda 3

1 Answer

How do I remover and replace 2002 dodge intrepid left headlamp assembly. Thanks Roger C.


on the upper radiator support above the headlamp there shoudl be 2 bolts with very small heads, (about 5.5 mm). Take these bolts out, they should be very long pins. once they are removed, headlamps can be removed out teh front.

Oct 16, 2010 | 2002 Dodge Intrepid

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    My 83 dodge mirada has 2 pins on the side of the carburator we adjusted them and now it either idles to high or low idk how to fix it


    adjust the left first then the right then the left again. when adjusting turn the screws counter clockwise until it stumbles turn clockwise untill it clears up plus half to three quarters turn. do that to the right , then left again

    Jun 16, 2010 | 1983 Dodge Mirada

    2 Answers

    Replace highbeam 1996 rodeo


    LIGHTING Headlights REMOVAL & INSTALLATION Non-Aerodynamic
    Fig. 1: Replacing a sealed beam headlamp

    bd06397.gif
    1. Disconnect the negative battery cable.
    2. Remove the front grille and/or headlight bezel.
    3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
    4. Before installing, spray some silicone grease into the bulb socket.
    5. Connect the wiring and install the bulb.
    6. Install the retaining rim and grille.
    7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.
    Aerodynamic

    Fig. 2: Replacing a headlamp bulb

    cf46ef4.gif

    Jul 24, 2009 | 1996 Isuzu Rodeo

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...