Cars & Trucks Logo

Related Topics:

d
dennis bader Posted on Apr 18, 2017
Be the first to answer

Replacing slide stop assembly - Cars & Trucks

Answer This Question

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Headlight exchange
Above each headlight assembly behind the radiator bulkhead there are two black "handles" that are for the latches that hold the headlights in place. Pull these handles up, and the headlight assembly should slide out the front. You can then replace the bulbs or, if you wish, the entire assembly. When done, just slide the assembly back in place and push the latch handles down. It should take about 5 minutes for each side.
Read full answer
Dec 28, 2013 • 1994 Oldsmobile Bravada
2helpful
2answers

How to change cv joints
I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.

    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Read full answer
Mar 22, 2012 • 1997 Chevrolet Cavalier
2helpful
2answers

Which side of the clutch does throw out bearing go on
The throw out bearing will be on the outside of the clutch assemble. What it does is push against the fingers in the center of the pressure plate.
Read full answer
Mar 08, 2011 • 1992 Acura Vigor
0helpful
1answer

Removal of head light assy 1989 ford ranger.
Hello,

To remove the front head light please follow the steps below:
  1. Place the Ford Ranger in "Park." Turn the engine off. Turn the headlights off. Remove the key from the ignition. Allow the truck to cool for about 20 minutes.
  2. Open the hood of the vehicle. Locate the two retainer pins on the headlight assembly of the light that needs to be replaced. Pry the retainer pins open with your finger. This releases the headlight assembly from the Ranger.
  3. Pull the headlight assembly forward. Unplug the electrical connector from the back of the assembly by hand. Rotate the retaining ring counterclockwise and slide it off the plastic bulb base.
  4. Pull the burned out bulb straight out of the headlight assembly. Discard the used bulb. Insert a replacement bulb into the headlight assembly and push it straight into the socket until it clicks into place. Slide the retaining ring around the bulb and rotate it clockwise to secure it.
  5. Plug the electrical connector into the back of the unit. Slide the headlight assembly back into the Ranger. Push the retaining pins back down to secure the headlight assembly.
Hope this helped. thank You for using FixYa!!!
Read full answer
Jan 19, 2011 • 1989 Ford Ranger
0helpful
1answer

2008 siverado. Front-end humming. Sounds like extremely loud tire pattern noise coming from left-front wheel area, noise stops when i turn the steering wheel to the right. replaced tire with no results.
it is your wheel bearing. the bearing is a sealed unit so you replace the hub assembly. remove wheel,caliper,brake rotor.if it is 4x4 loosen axle nut. there are three 15mm bolts on back side of spindle remove these and slide hub out replace with new one. most hubs come with new wheel speed sensor so remove harness from connectors or if no new one remove the screw holding it in place to hub and slide out.
Read full answer
Dec 31, 2010 • 2008 Chevrolet Silverado 1500
0helpful
1answer

TO JTURCOTE, THANK YOU BUT MY SWITCH DOES NOT LOOK LIKE THE ONE IN THE DIAGRAM. MINE IS MOUNTED HIGH ON THE BRAKE PEDAL ARM BUT IS NOT CONNECTED TO THE MASTER CYL. PUSH ROD. HELP
Sorry. That is the one autozone.com calls for in your car. there is another one in the book for the other trucks. Does yours look like this? If so, instructions pasted below.

f1bffee.gif
Fig. 1 Exploded view of the brake light switch
  1. Lift the locking tab on the switch connector and disconnect the wiring.
  2. Remove the hairpin retainer, slide the stop lamp switch, pushrod and nylon washer off of the pedal. Remove the washer, then the switch by sliding it up or down.

On trucks equipped with speed control, the spacer washer is replaced by the dump valve adapter washer.
  1. To install the switch, position it so that the U-shaped side is nearest the pedal and directly over/under the pin.
  2. Slide the switch up or down, trapping the master cylinder pushrod and bushing between the switch side plates.
  3. Push the switch and pushrod assembly firmly towards the brake pedal arm. Assemble the outside white plastic washer to the pin and install the hairpin retainer.



CAUTION Don't substitute any other type of retainer. Use only the Ford specified hairpin retainer.

  1. Assemble the connector on the switch.
  2. Check stop lamp operation.
Read full answer
Sep 24, 2010 • 1999 Ford Expedition
0helpful
1answer

I have a 2007 grand caravan front wheel drive that needs a new rear bearing hub assembly. I have removed all except the assembly and it will not budge. Is there anything I can use to remove the hub other...
CHRYSLER WARNED AGAINST NOT USING A SLIDE HAMMER PULLER UNLESS YOU ARE GOING TO REPLACE REAR HUB AND BEARING ASSEMBLY.WHEN REPLACING HUB AND BEARING ASSEMBLY THEY HAS TO BE PRESSED OUT.
Read full answer
Sep 21, 2010 • 2007 Dodge Grand Caravan SXT Minivan
0helpful
1answer

How do I replace a head light for a 2000 Chevy Malibu
under hood on top of headlight assembly, there are two plastic slide pins. pull up on these slide pins to release headlight assembly. then you will have enough of room to change bulbs. when putting assembly back on car, push in on assembly while putting pins back down. to secure headlight assembly.
Read full answer
Mar 08, 2010 • 2000 Chevrolet Malibu
1helpful
1answer

How do I replace the bulb in the high mount stop light?
Please look at the bottom of your tail lights there is 1 flat head screw there. Take it out and you can slide tail light out. You will find the back of the bulb there. Be care when returning the assembly back in place as it slide up and then you just replace the screw.
Read full answer
Mar 15, 2009 • 2004 Chrysler PT Cruiser
0helpful
1answer

Replace headlight bulbs
Open the hood. On the top of the headlamp assembly are two 3/8 inch bolts. Remove them. Between the two (down in a hole) is another 3/8 inch bolt; it's very long, as it screws into the bottom of the assembly. Remove it, too. Slide the entire assembly forward. It's tricky because the edges get caught on the surrounding structures, but it will slide out. Remove the round rubber stopper from behind the assembly to expose the lamp. Rotate the lamp slightly and remove it. Carefully lift the retaining clips and slide the lamp off the plug. Be careful not to touch the glass on the replacement lamp; oil from your skin can cause halogen lamps to fail. Slide the new lamp onto the plug until it clicks, then put everything back in reverse order.
Read full answer
Oct 18, 2008 • 2005 Ford Expedition
Not finding what you are looking for?

View Most Popular

Cars & Trucks

Related Question

Headlight exchange

  • 1994 Oldsmobile Bravada

15 views

Ask a Question

Usually answered in minutes!

Popular Questions

Toyota dashboard CD player won't eject

2003 Toyota Celica

4.3 Firing order diagram for 4.3L v6 Chevy engine

1999 Chevrolet K1500

BMW X5 Trans Fail Safe Program,

BMW X5 Series Cars & Trucks

Diagram of 1996 ford ranger fusebox which fuse is

1996 Ford Ranger SuperCab

What does my check engine light trouble code $7e8 mean?

2009 Chevrolet HHR 2.4

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
DIS9_Full.pdf. user-manual-1994...

1994 Land Rover...

PDF Manual
DIS9_Full.pdf. user-manual-1994...

1994 Land Rover...

PDF Manual
Rhonda_Docs.pdf. user-manual-2001...

2001 Nissan Sentra

Loading...