Question about Cars & Trucks

Open Question

Rear driver side inside door removal of component that that holds glass

Fixing the lock on the rear driver door but got stuck at the white plastic object that holds the glass in place. which is needed off to get to the lock part of the inside of the door. theres a round plastic like bolt going through the plastic that holds the glass on each side

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
sicaudio
  • 96 Answers

SOURCE: Driver's side door power locks are stuck; door stuck shut.

sounds like the rods are disconnected the clips hold the rods in place the latching mechanism holds the handle in place as well did you replace the speakers or did a shop? if a shop did then they caused this if you did then you may have caused this either way untill you reattach the rods none of it will work. you will have to manually open the door at the latch from inside teh door behind the panel.

Posted on Jul 19, 2008

Ad
  • 328 Answers

SOURCE: How do you remove the door panel on a 1997 GMC 1/2 ton trucks?

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008f768
Hope this helps!

Posted on Feb 16, 2009

  • 42 Answers

SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Posted on Mar 20, 2009

  • 1986 Answers

SOURCE: 04 Chevy Aveo Lock

The screw that you require will actually be an M6-1/2" bolt and a washer as well because the original bolt is more like 1/3". M6 is the metric measurement for the threading and the bolt is 1/2" long. The Hexagonal should be 10mm. I went to Home Depot for my bolt.

Posted on Aug 07, 2009

  • 1 Answer

SOURCE: Door lock assembly fell inside door

The same thing happened to my 2006 Aveo. Once you do the above find the lock and the screw that holds it in (they will both be in the bottom of the door). Put the lock back in place, put blue Loctite on the screw and screw it back in place and this problem will not repeat itself.

Posted on Aug 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda odyssey door lock driver side


Pop off the door panels & remove the plastic film. There's a white plastic actuator attached to the lock. You can test for voltage from the connector, but unlikely that's the problem. My symptom was the actuator was moving but not actually locking. It turned out mine was loose and I fixed mine by just reattaching the actuator. There's several screws holding it in there and mine came loose. Use lock-tite because it came loose a second time. If the motor isn't functioning then if you disassemble the actuator you might be able to search on EBay for a motor - the rear tailgate uses a Mabuchi. Otherwise you will need to replace the actuator. The rear one is about $80 online.

Mar 18, 2013 | 1999 Honda Odyssey

1 Answer

2005 dodge durango rear hatch will not unlock to open


I own a 04 durango and the door lock actuator froze up internally and I could not open the rear hatch. After hours of research on my computer nothing seemed to fix the problem. I eventually figured it out myself. You must pull the screws out of the molding on the inside of the rear door. You can now pull the molding toward you and look down at the actuator and latch. You can pull on the molding quite a bit if necessary. I never broke mine and I was pretty agressive with it. Now, on top of the whole mechanism is the lock actuator. There should be a white plastic lever sticking out towards the driver side. If you can slide it from back to forward "forward is front of vehicle", the lock should be working. If not your door is not unlocking. My durango had 3 Torx screws on top of the actuator. Remove them. This will take the actuator off of the latch. Now that the actuator is not binding or holding the lock from moving, again try to move the white plastic lever towards front of vehicle. It should click and you should be able to open the door.

Oct 12, 2011 | 2005 Dodge Durango

1 Answer

2006 Chevy Impala drivers side rear door stuck from outside and inside. How do I remove door panel with door shut?


here is a picture of the door panel components:acceptwha619.gif
those numbered 2 and 4 are screws 7 and 8 are plastic fasteners that should just pull out the door frame with an a little force outward on the plastic door panel.

May 03, 2011 | 2006 Chevrolet Impala

2 Answers

Back door latch broke cant open back door where can i buy the part and the name of the part


I just bought the part last week for 61.76 from the dealership. It takes about two hours to unscrew the strap from the inside, remove trim from the inside starting at the top, sides and bottom. Remove the license plate from the outside of the hatch. Next remove the 8 bolts (10mm)and 3 white plastic tabs that snap on from the large black plate and move to the side (you don't need to disconnect the wires). From here you can reach around the rear window unit and open the door by moving the latch or pulling the cable. You should remove the 4 nuts that hold on the rear window assembly and move the to reach two nuts which holds the center portion of the trim piece you are trying to remove. There should be a plastic piece covering the cable and latch, it just pops off by pulling it straight out. There are three plastic tabs in the corners and one screw (lock for the hatch) that holds on the license plate assembly to the rear hatch along with two white plastic tabs which are located at the bottom two holes for license plate. These plastic tabs come in from the front. Use pliers to squeeze the together and push. You will need to disconnect the license plate lamp wire connector from the left side. The license plate assembly should drop away. Two screws hold on the latch, remove and replace and reverse proceedure.

Jul 08, 2009 | 2002 Toyota Sequoia

1 Answer

2004 Durango Rear Hatch Stuck Closed


I own a 04 durango and the door lock actuator froze up internally and I could not open the rear hatch. After hours of research on my computer nothing seemed to fix the problem. I eventually figured it out myself. You must pull the screws out of the molding on the inside of the rear door. You can now pull the molding toward you and look down at the actuator and latch. You can pull on the molding quite a bit if necessary. I never broke mine and I was pretty agressive with it. Now, on top of the whole mechanism is the lock actuator. There should be a white plastic lever sticking out towards the driver side. If you can slide it from back to forward "forward is front of vehicle", the lock should be working. If not your door is not unlocking. My durango had 3 Torx screws on top of the actuator. Remove them. This will take the actuator off of the latch. Now that the actuator is not binding or holding the lock from moving, again try to move the white plastic lever towards front of vehicle. It should click and you should be able to open the door.

Jun 09, 2009 | 2004 Dodge Durango

1 Answer

2000 Buick Lesabre: Driver Door 1. Do I have to disarm the air bags to replace glass? 2. How do I pry off the inside driver side door panel components? 3. HOw do I replace the inside driver side...


Hello, NO you don't have to disarm airbags for glass.
You can pry off the door panel with big flathead screw driver. The panel is held on by plastic tabs that pry off and you can press them back on with fingers.
Before prying off panel, you should pry off electric window button panel. Also remove any screws that are visible. Sometimes the arm rest has little plastic covers with screws underneath it.
This is actually easier than it sounds.
Just remove any visible screws, and pry it off and lift up and she'll come off.

May 15, 2009 | 2000 Buick LeSabre

1 Answer

Driver door lock shoved inside door. (someone tried to break in) I need a schematic or diagram of the door. How to take it apart, what it looks like inside to try and fix this. Can anyone help?


I had same problem. it was not broken into. the screw that holds lock cylinder in fell out. to get inside door is easy. remove screws around border all sides of door and one in middle near speaker. the gentley snap door away from the two clips on inside and lift up off window opening . peel back plastic and you will see the lock mechanism. if need be ( i had to) you can unplug the automatic locks, window and other electric harnesses attached to door inside cover. the lock cylinder will be in bottom of door w/ a brass hex screw. there is a white piece of plastic insert in the hole of lock mechanism and reattach (snap onto bar). its all easy no schematic needed if you have a lil mechanic ability. good luck.

May 02, 2009 | 2004 Suzuki Forenza

1 Answer

2005 dodge durango rear hatch is down and will not open


I own a 04 durango and the door lock actuator froze up internally and I could not open the rear hatch. After hours of research on my computer nothing seemed to fix the problem. I eventually figured it out myself. You must pull the screws out of the molding on the inside of the rear door. You can now pull the molding toward you and look down at the actuator and latch. You can pull on the molding quite a bit if necessary. I never broke mine and I was pretty agressive with it. Now, on top of the whole mechanism is the lock actuator. There should be a white plastic lever sticking out towards the driver side. If you can slide it from back to forward "forward is front of vehicle", the lock should be working. If not your door is not unlocking. My durango had 3 Torx screws on top of the actuator. Remove them. This will take the actuator off of the latch. Now that the actuator is not binding or holding the lock from moving, again try to move the white plastic lever towards front of vehicle. It should click and you should be able to open the door.

Feb 08, 2009 | 1995 Subaru Legacy

1 Answer

REPLACIND DRIVER SIDE WINDOW REGULATOR


Pull out window crank and door handle, remove panel, remove plastic Nylon that's between metal and panel, crank the window down enough to see the arm and the part that connects with glass. Make sure the metal part inside the door that comes from an arm and attaches to glass is clean, from broken glass and the gap that attaches to window is clean,bend the new glass to make it fit inside the opening slide down the new glass from the top using opening guides, grave it from both sides standing in between and make land on top center of the part that graves the glass, put automotive glass silicone on center of that part,just at where graves the glass, let dry, put the plastic back the door panel the window crank with the "U" shaped lock washer and the door handle, I hope I was clear

Jan 21, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

Rear window regulator line broken


Hi lec the rear glass has a white plastic clip holding the glass to the regulator. try from  the door side, pushing the center plastic pin out toward you then the glass will lift out   D

Jan 15, 2009 | 2000 Jaguar S-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...