Question about Jeep Grand Cherokee

1 Answer

How do you remove nylon fasteners for the front bumper facia and grill on a 1999 grand Cherokee Laredo?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

I usually pull the fascia and pry with a flat head. Check out this link.... It should help some..

Posted on Apr 19, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Where is the ambient temperature sensor located on the 1999 grand cherokee laredo

ambient temperature sensor located behind front grille mounted to bracket on the radiator.

Feb 28, 2012 | 1999 Jeep Grand Cherokee

1 Answer

2011 Dodge Caravan. Ran into a metal wheelchair ramp rain. Drove back - dislodged - the black trim insert near the bottom of the plastic bumper cover. That black plastic thing has to be just put back on...

Hello are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.


Dec 02, 2011 | Cars & Trucks

1 Answer

Where in my1999 grand cherokee is my electric fan relay switch

The 1999-2004 Jeep Grand Cherokee fan relay is under the right front portion of your bumper support. The Bumper is easy to remove and is a 2 piece system. Take out your headlights (1 7mm bolt on each one), then take out all the 7mm bolts on the grill. Look up in thefront fender wells and there is 1 10mm bolt on each side with 3 or 4 plasctic rivits (cut the head off and push them through and replace with new plasctic rivits from your local parts store and make sure you have a plastic rivit setting tool). There is 3 plastic inserts under the bumper, pull the heads off, then pull the insert out. Your grill and bumper cover will then come off. The next part is to remove all of the Torx T27 bolts. Then disconnect the ambient air temperature sensor on the passenger side by the radiator. There is 2 clips (1 on each side) That hold the plastic in. Depresses them with a small pair of needle noise pliers. Push the air box clip through and the ambient air temperature sensor harness clip through. Once the plastic frame is off, release the electrical connectors for the head light harness, then the whole frame comes off. Once the frame comes off, on the passneger side is the fan relay. I like to use the after market Dorman fan relay because it comes with a new electrical pigtail. It is available from your local parts store. Dorman Part # 902-303. Good Luck

Jun 15, 2010 | 1999 Jeep Grand Cherokee

1 Answer

2006 jeep grand cherokee bumper removal

check your metal bumper retainers attached to the front chassis there must be a hidden bolts and nuts thats still on that you havent seen yet remove it and take off the bumper bar( steel bumper)

Apr 07, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How to replace the front bumber on a 1999 grand am?

Jack the car up and put it on jack stands. Disconnect fasteners retaining the splash apron under the radiator. These form part of the wheelwells on each side. Remove the fascia where it is attached to the fenders. Each side will have 4 bolts. remove the 2 bolts i bottom of the bumper they will be on each side of the license plate in the front. Remove the 2 upper bolts in the grille area. This will allow you to remove the bumper skin. To remove the impact bumper remove the u bolt on each side they each have 2 nuts. remove the bumper

Feb 03, 2010 | 1999 Pontiac Grand Am GT

3 Answers


The relay is under the right front headlamp assembly and bracket. You can access it two ways. Remove the front bumper facia, headlights, and bracket assembly. The grill is part of the facia and the headlight bracket runs all the way across the front. Or you can remove the right headlamp and use a hole saw to cut through the bracket, it is a plastic material.

Apr 25, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Trying to take out headlight in 2005 jeep grand cherokee laredo. have grill off and screws

  1. Disconnect and isolate the battery negative cable.
  2. Remove the headlamp cover TOP
    1. Remove the mounting fasteners.
    2. Disconnect the headlamp unit electrical connector BACK
    3. Separate the headlamp from vehicle.CAUTION: Do not touch the bulb glass with fingers or other oily surfaces. Reduced bulb life will result.

      NOTE: If installing a new headlamp unit, transfer all the wiring, bulbs, and sockets to the new unit.

      1. Install all of the bulb sockets in headlamp .
      2. Position the headlamp on the vehicle.
      3. Connect the electrical connector .
      4. Push the headlamp inward to secure into position.
      5. Install mounting fasteners
      6. Install cover over headlamp.
      7. Connect battery negative cable

Jan 13, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Front bumper removal

Plastic rivets in the wheel wells, clips under the headlights, remove the grill, plastic clips under the front,
too much to write.
Go get a repair manual

Sep 30, 2008 | 2001 Jeep Grand Cherokee

2 Answers

I got a 99 jeep grand cherokee laredo with a 4.0 straight 6 and looking for the radiator fan relay...any suggestions???

It's behind the passenger headlight.Need to take off grill,bumper fascia to get access to it.Mine took about an hour alltogether.

Jul 18, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides