Question about Geo Cars & Trucks

Open Question

Changed the timing belt and now the engine knocks on a 1993 geo tracker

The only thing we did was can get upper and lower seal water pump and timing belt it runs great just knocks badly now

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 337 Answers

SOURCE: 1992 geo tracker will not run

The ECM has a blown capacitor inside it for opening the injector you will most likly need to get it rebuilt, buy a new ,or used ECM had the same problem with my sidekick.

Posted on Mar 16, 2009

daves944
  • 1050 Answers

SOURCE: Aligning the crank and cam on a 1996 Geo tracker

Use this to align the sprockets, it's critical, you risk engine damage if it is not correct.119164a.jpg

Posted on May 01, 2009

  • 1757 Answers

SOURCE: looking for timing belt diagram on 97 Geo Tracker

Click on the following free, direct Link. It has the Timing Belt Diagrams, including Marks and Instructional Diagrams.

Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1997/make/geo/model/tracker/1997_geo_tracker_timing_belt_diagram_marks.htm

Posted on Apr 08, 2010

ZJLimited
  • 17970 Answers

SOURCE: how to replace the water pump on a 1992 geo

Water Pump - REMOVAL & INSTALLATION
During these procedures, identify all components removed from the engine so that they may be reinstalled in their original positions. If discarding the old components so that new components can be installed, identifying the old items is not necessary.


1.3L and 1.6L Engines

  1. Remove the timing belt cover, timing belt, tensioner, plate and spring.
  2. Remove the water pump mounting bolts.
  3. Remove the one (1.6L MFI engines) or two (1.3L and 1.6L TFI engines) small rubber seals from between the water pump and the oil pump, and the water pump and the cylinder head.
  4. If necessary for clearance, remove the oil level dipstick tube retaining bolt from the engine block and the alternator adjusting brace.
e6f342c.jpg

Fig. 1: Exploded view of the water pump mounting

WARNING Do NOT use a prybar between the water pump housing and the engine block to separate the two components; this can cause scratches and/or gouges, which can prevent proper sealing.
  1. Pull the water pump off of the engine block. If the water pump is difficult to remove from the engine block, use a soft-faced mallet to tap the water pump housing until it loosens.
Do not disassemble the water pump; if the water pump is damaged or defective, the entire unit is replaced.
  1. Thoroughly clean the water pump gasket mating surfaces of old gasket material and corrosion.
To install:
  1. Along with a new gasket, install the water pump on the engine block. Tighten the water pump mounting bolts to 88-115 inch lbs. (10-13 Nm).
  2. On 1.3L and TFI 1.6L engines, install two new rubber seals: one between the water pump and oil pump, and the other between the water pump and the cylinder head. The MFI 1.6L engines only use one rubber seal, located between the water and oil pumps.
  1. If removed, install the alternator adjusting brace and the oil level dipstick retaining bolt.
  2. Install the timing belt, tensioner, plate, spring and cover.

Hope helps (remember comment and rated this).

Posted on Jul 19, 2010

mickha2
  • 145 Answers

SOURCE: 1993 geo tracker engine idels high

1 remove intake cover
2 spray carb cleaner INTO IDLE SPEED CONTROL HOLE
3 shut off engine
4 spray carb cleaner INTO IDLE SPEED CONTROL HOLE
5 wait 5 min
6 start engine

if does not help yse seafoam through pcv hose

Posted on Aug 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where on engine block do you find water pump


that's easy, its a G16 engine
here, is the photo of doing just that.
see the 7/07 mark, BINGO
at 60k a new belt is done and since the pump is in the way, we
replace it too. use a gates belt.

http://www.fixkick.com/t-belt/donebelt1.jpg

Jun 09, 2014 | 1993 Geo Tracker

1 Answer

How to find the timing marks on a 1993 geo tracker


on what, spark or cam???
this engine 1 of 2, has cam belt timed
and a distributor timed... know that as a fact;. please.

http://www.fixkick.com/t-belt/16-fast-belt-install.html

that is cam. on 16v only
the pages there cover both engine,, G16a and B.
TBI 8valve and MPI 16v engine.

Jan 24, 2014 | 1997 Geo Tracker 2 Door

1 Answer

Oil leak front engine timing chan


1995 Tracker would have a timing BELT. Normal oil leak points (in order) on a Suzuki G16 engine are the distributor base (rear of motor), valve cover (top of motor), front main seal (behind lower timing belt cog) cam seal (behind the upper timing belt cog) and rear main seal. (behind the flywheel). I'd suspect the front main seal or cam seal. I use foot power to help find oil leaks.

Dec 24, 2012 | 1995 Geo Tracker

1 Answer

How to replace the water pump on a 1992 geo tracker 1.6 liter engine


Water Pump - REMOVAL & INSTALLATION
During these procedures, identify all components removed from the engine so that they may be reinstalled in their original positions. If discarding the old components so that new components can be installed, identifying the old items is not necessary.


1.3L and 1.6L Engines

  1. Remove the timing belt cover, timing belt, tensioner, plate and spring.
  2. Remove the water pump mounting bolts.
  3. Remove the one (1.6L MFI engines) or two (1.3L and 1.6L TFI engines) small rubber seals from between the water pump and the oil pump, and the water pump and the cylinder head.
  4. If necessary for clearance, remove the oil level dipstick tube retaining bolt from the engine block and the alternator adjusting brace.
e6f342c.jpg

Fig. 1: Exploded view of the water pump mounting

WARNING Do NOT use a prybar between the water pump housing and the engine block to separate the two components; this can cause scratches and/or gouges, which can prevent proper sealing.
  1. Pull the water pump off of the engine block. If the water pump is difficult to remove from the engine block, use a soft-faced mallet to tap the water pump housing until it loosens.
Do not disassemble the water pump; if the water pump is damaged or defective, the entire unit is replaced.
  1. Thoroughly clean the water pump gasket mating surfaces of old gasket material and corrosion.
To install:
  1. Along with a new gasket, install the water pump on the engine block. Tighten the water pump mounting bolts to 88-115 inch lbs. (10-13 Nm).
  2. On 1.3L and TFI 1.6L engines, install two new rubber seals: one between the water pump and oil pump, and the other between the water pump and the cylinder head. The MFI 1.6L engines only use one rubber seal, located between the water and oil pumps.
  1. If removed, install the alternator adjusting brace and the oil level dipstick retaining bolt.
  2. Install the timing belt, tensioner, plate, spring and cover.

Hope helps (remember comment and rated this).

Jul 19, 2010 | 1991 Geo Storm

1 Answer

1993 Geo Tracker leaking water from upper middle of engine. Do you think it might be a head gasket?


I would check hoses and water pump. When water pump goes bad it leaks water out hole out of bottom.Get pressure pump and pump up system it makes it easier to find leak.

Jul 16, 2010 | 1993 Geo Tracker

1 Answer

How do i take off the old water pump on 1996 geo metro 4 cyl?


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air cleaner.
  4. Remove the suction pipe bracket for the A/C compressor, if equipped.
  5. Loosen but do not remove the 4 water pump pulley bolts.
  6. Raise and safely support the vehicle.
  7. Remove the lower splash shield.
  8. Remove the A/C compressor drive belt, if equipped.
  9. Remove the alternator drive belt.
  10. Remove the crankshaft and water pump pulleys.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts and remove the water pump from the engine.


ae1b66e.gif
Water pump mounting location

  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten the bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten the bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and tube.
  7. Install the timing belt.
  8. Install the water pump and crankshaft pulleys. Leave the water pump pulley bolts hand-tight.
  9. Install the alternator drive belt.
  10. Install the lower alternator cover plate and tighten the bolts to 89 inch lbs. (10 Nm).
  11. Install the A/C compressor drive belt, if equipped.
  12. Install the lower splash shield and lower the vehicle.
  13. Tighten the water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  14. Adjust the water pump drive belt tension and tighten the alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  15. Install the suction pipe bracket for the A/C compressor, if equipped.
  16. Install the air cleaner.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and check for leaks.


83667f6.gif Water pump assembly showing rubber seal location


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

    CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  3. Remove the air cleaner assembly.
  4. Loosen but do not remove the four coolant pump pulley bolts.
  5. Raise and support the vehicle safely.
  6. Remove the lower splash shield.
  7. Remove the air conditioner compressor drive belt.
  8. Remove the lower alternator cover plate bolts, loosen the alternator adjusting bolt, and remove the drive belt.
  9. Remove the crankshaft pulley.
  10. Remove the coolant pump pulley.
  11. Remove the timing belt.
  12. Remove the oil level dipstick and guide tube.
  13. Remove the alternator adjusting bracket from the water pump.
  14. Remove the water pump rubber seals.
  15. Remove the water pump mounting bolts and nuts. Remove the water pump from the vehicle.
To install:
  1. Clean the gasket mating surfaces thoroughly.
  2. Check the water pump by hand for smooth operation. If the pump does not operate smoothly or is noisy, replace it.
  3. Install the pump using a new gasket. Tighten bolts to 115 inch lbs. (13 Nm).
  4. Install new rubber seals.
  5. Install the upper alternator adjusting bracket and tighten bolt to 17 ft. lbs. (23 Nm).
  6. Install the oil level dipstick and guide tube.
  7. Install the timing belt.
  8. Install the water pump pulley and leave the bolts hand tight.
  9. Install the crankshaft pulley.
  10. Install the water pump/alternator drive belt.
  11. Install the lower alternator cover plate and tighten bolts to 89 inch lbs. (10 Nm).
  12. Install the air conditioner compressor drive belt by releasing the tensioner pulley and installing belt.
  13. Install the lower splash shield and lower vehicle.
  14. Tighten water pump pulley mounting bolts to 18 ft. lbs. (24 Nm).
  15. Adjust the water pump drive belt tension and tighten alternator adjustment bolt to 17 ft. lbs. (23 Nm).
  16. Install the air cleaner assembly.
  17. Refill the cooling system.
  18. Connect the negative battery cable.
  19. Start the engine and allow it to reach operating temperature. Check for leaks and refill cooling system as necessary.

Mar 06, 2010 | 1996 Geo Metro

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

3 Answers

I need a diagram of engine timing marks for a 1.6 litre engine


1996 Geo Truck Tracker 2WD 1.6L MFI SOHC 4cyl

2efa731.jpg

Fig.: Before installing the timing belt, position the camshaft sprocket (1) so that the timing mark on the sprocket (2) is aligned with the notch (3) on the inside timing belt cover (4) ...

5a2ee07.jpg

Fig.: ...and ensure that the crankshaft sprocket (1) timing mark (2) is aligned with the mark on the oil pump (3)

For more details, can register in autozone.com (free).

I hope help you with this (remember rated this help) Good luck.

Oct 15, 2009 | 1996 Geo Tracker 2 Door

2 Answers

Power steering


look thru the front hold of pS pulley
see bolt hole (missing bolt now)
replace this bolt and belt
then tension it.
then tighten this missing bolt.

done.
just like mine.
im doing a timing belt now.
this is an interference motor , you do too.

Apr 07, 2009 | 1993 Geo Tracker

1 Answer

Where is the water pump on 93 geo prism, small engine


You're right. it could very well be your water pump, but I would suggest replacing your thermostat before trying to tackle replacing your water pump. However, if your thermostat turns out not to be the problem, I have enclosed step-by-step instructions for removal and re-installation of your water pump. Hope this proves to be helpful. Have a nice evening!


1993
Geo Prism Water Pump Removal/Installation
  1. Disconnect the negative battery cable. Drain the engine coolant from the radiator.
  2. Remove all drive belts.
  3. Support the engine using suitable equipment. Place a wooden block between the jack and engine. Remove the right engine mount and insulator.
  4. Remove the No. 3 (upper) and No. 2 (middle) timing belt covers.
  5. If equipped with power steering, raise and safely support the vehicle. Remove the front transaxle mount. Lower the vehicle, remove the cooling fan assembly.
  6. Remove the mounting bolt for the dipstick tube; remove the tube and dipstick. Immediately plug the hole in the block to prevent fluid from contaminating the oil.
  7. Remove the electrical connector for the coolant temperature sending unit.
  8. Remove the 2 nuts securing the engine coolant pipe to the cylinder block.
  9. Loosen the hose clamp and remove the coolant inlet pipe from the vehicle.
  10. Loosen the hose clamp and remove the coolant inlet hose from the water pump.
  11. If equipped with power steering, raise the engine and remove the mounting bolts for the water pump. Remove the water pump and O-ring from the vehicle.
To install:
  1. Install a NEW O-ring to the vehicle. Install the water pump and torque the retaining bolts EVENLY to 11 ft. lbs.
  2. Lower the engine if necessary, and connect the coolant hose to the water pump. Reconnect the engine coolant inlet pipe to the vehicle and secure to hose with clamp and secure to block with 2 nuts. Tighten the engine coolant inlet pipe nuts to 11 ft. lbs.
  3. Connect the electrical connector for the coolant temperature sending unit.
  4. Install the oil guide tube and torque the retaining bolt to 84 inch lbs. Install the oil level indicator to the guide tube.
  5. Install the radiator fan assembly, if necessary.
  6. If equipped with power steering, raise and safely support the vehicle. Install the front transaxle mount. Torque the through bolt nut to 64 ft. lbs. and 2 mount nuts to 47 ft. lbs.
  7. Lower the vehicle (if necessary) and install the No. 3 (upper) and No. 2 (middle) timing belt covers.
  8. Support the engine using suitable equipment. Install the right engine mount and insulator.
  9. Remove all engine lifting equipment.
  10. Install and adjust all drive belts.
  11. Reconnect the negative battery cable. Fill the cooling system. Start the engine and check for coolant leaks.

Nov 23, 2008 | 1993 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...