To reset the pass word on Secustar EA/ES/EH I had to unscrew a red button near the hinge thus remove the rear housing. In doing so the black wire disconnected. Where do I connect it?

Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Dec 19, 2016 | Cars & Trucks

1 Answer

Remove rear seat

Rear seat cushion-fold forwards,release plastic clip from hinge,remove wiring multiplug if applicable.Lift out cushion.(40% backrest)Tilt forward approx 20degrees,use a screwdriver to release catch retainer on outer pivot pin.lift backrest and withdraw from inner pivot pin.Lift the backrest from inside vehicle.(will only lift out if backrest is tilted forward 20degrees from verticle. 60% section can then be removed on saloons by releasing the lock with a finger and pulling from the anchor pins.On estates unscrew centre seat belt lower mounting and unscrew hinge pin from centre support. unhook upholstery clip and lift backrest from lefthand side mounting.slide backrest towards the door to release centre pinlug and withdraw backrest from inside the vehicle. Refit in reverse order.

May 22, 2015 | 1999 Saab 9-5

1 Answer

Neither the driver's side or pass. side windows will work. Rear windows work.

What kind of car?? But check wiring. Open drivers door and between the hinges you will see a black rubber housing. Inside that housing are all the wiring that go to that door. Peel it back and check for broken wires. Every time the door is opened and closed those wires are bent back and forth and over time they will break not all of them but usually the window wires will because they are the thickest. All your windows rely on the main switch in that door to function properly.

Mar 04, 2013 | Cars & Trucks

1 Answer

95 buick lesabre door jam button that turns dome light on and off

the button is at the door hinge by the weather seal it takes a 3/8 wrench or a socket to remove and replace,don't let the two wires touch it will blow a fuse they are about $5 at part house good luck...

Oct 31, 2012 | Buick Cars & Trucks

1 Answer

How do you remove the lift gate or rear hatch from my 2000 Dodge Durango? I see the bolt on the hinges but I don't know where to un plug the wiring..

I haven't had one apart, but i would guess behind the head-liner near where the harness passes through the body. similar to my wife's 08.

Sep 24, 2012 | Cars & Trucks

1 Answer

2002 suburban has leak in driver side rear floor. Cannot see where water would be coming from?

We had same--water on driver side rear floor (soaked!). Driver side front floor seemed dry until feeling UNDER rug, was slightly damp. We found the location of TWO leaks causing this.

Leak #1 was through the parking brake line/cable seal; Recaulked with silicone. Removed plastic trim on floor between floor and door to reveal metal channel filled with water.

Leak #2 was where the door meets the car, near the hinge. It was the accordian-looking tube housing the wiring for the door. The big, rubber, circular plug connecting it to the main part of the car had come loose and water ran down through that, into the SAME metal channel filled with water from leak #1; will seal with silicone.

Note: We found that the channel filled extensively near the front door, BUT the carpet edge from the floor near the rear seat was dipping into it, wicking it up to the rear floor. Also, upon acceleration, the water in the channel gushed toward the back, thus soaking the rear carpet.

These leaks were found by removing all plastic trim (covering edges of carpet by doors), then one of us pouring water into specific areas of the exterior of the vehicle, and the other one watching closely with a flashlight for any signs of dripping.

Feb 18, 2010 | 2002 Chevrolet Suburban

2 Answers

I cannot find the reset button for the fuel pump. Could you tell me I can find it?

there is no reset button on the fuel pump

Dec 17, 2009 | 1994 Ford Explorer Limited

1 Answer

I need the factory wiring radio color codes to a mazda 626 99 es so i can hook up my new alpine deck

Hi

The wiring color codes for 1999 Mazda 626 are--

Constant 12V+ Blue/Red
Switched 12V+ Blue/White
Ground n/a
Illumination Red/Black
Dimmer n/a
Front Speakers 6" x 8" Doors
Left Front (+) Green/Orange
Left Front (-) Green/Black
Right Front (+) Green
Right Front (-) Yellow/Green
Rear Speakers 6" x 9" Rear Deck
Left Rear (+) Blue/Green
Left Rear (-) Blue
Right Rear (+) Blue/Black
Right Rear (-) Blue/Orange
Please do rate the solution & revert for further assistance.

Thanks
Rylee

Jul 31, 2009 | 1999 Mazda 626

1 Answer

How do you replace the backup light bulbs on a 2001 TDI Beetle?

The rear tail lights can be removed by unscrewing the lamp module from inside your trunk, it's a large black knob that you can push on once it's unscrewed to make the lamp module pop out of the bumper socket. The "white" tail lights are accessed from underneath the car by reaching up behind the rear bumper.

Jul 10, 2009 | 2001 Volkswagen Beetle

1 Answer

Rear Window Sprayer not working.

Rear washer pump is located near bottom of washer reservoir, below the left front wheel house extension and between left inner and outer fenders. Have some operate the rear washer switch while you listen in this area to find out if the the pump is running. The hose from the pump routes up along side the reservoir filler neck, into the engine compartment. Just aft of the reservoir neck an in-line connector joins the hose to the engine compartment hose. The engine compartment hose travels the top left front fender wheel house to the dash panel, passing through a grommet into the passenger compartment. In the passenger compartment, another connector joins the engine compartment hose, and then up through the front driver pillar to the headliner, then above the headliner along the left roof to the rear of the vehicle. It comes out above the lift gate, in the hinge gap, and into the lift gate to the nozzle.

Not likely to be stopped up. First find out if the pump is running, and that there's fluid in the reservoir. Look for fluid running out somewhere near the reservoir. The pump isn't running, or the hose is disconnected around the tank. Look for leaks (when running the pump, and reservoir filled) at the lift gate hinge joint.

Jul 25, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?

View Most Popular

Cars & Trucks

How to disconnect a BCM in a chevy colorado 2007

Cars & Trucks

Open Questions:

0 Answers

How often do I need to put water in the batteries and what pump do I need.also should I leave it on charge whenever it’s not in use

Apr 19, 2018 | Cars & Trucks

0 Answers

2003 pontiac aztec power windows do not work-new switch worked 2 days only all fuseckecked ok

Apr 19, 2018 | Pontiac Cars & Trucks

0 Answers

2001 chevy lumina stalling and surging fix fuel filter

Apr 19, 2018 | Cars & Trucks

0 Answers

I got a 16kg washingmachine with no power completely dead .what do I check for fault finding

Apr 19, 2018 | Cars & Trucks

Ask a Question

Usually answered in minutes!

Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Cars & Trucks Experts

yadayada

Level 3 Expert

78238 Answers

Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins

Level 3 Expert

14405 Answers

Have a manual for Cars & Trucks? Or just drag it here!

6ya staff · Answer 1 · 1/2/2017 12:00:00 AM

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Steve Allison · Answer 2 · 12/11/2008 12:00:00 AM

You should really have the service manual at hand; they will contain color coding of all of the wiring. Either Haynes or Chilton will have all the electrical diagrams and the most serivce work you can do at home on the mechanical stuff. They cost between 20-30 dollars US and can be had at auto parts stores.

Many horns are not directly controlled by the horn button but by a relay on which the horn button works.

fz66 · Answer 3 · 12/25/2009 12:00:00 AM

fz66

6 Answers

SOURCE: How do i remove rear bench seat from 08 lancer es

you pull up firmly on the front of the bottom side of the back seat it will pop up, one clip on each side between where your legs would go.

Posted on Dec 25, 2009

dttech · Answer 4 · 8/13/2011 12:00:00 AM

Are you talking about the door handle hinge? The door handle and hing do not need to be removed to remove the door panel. Remove the door handle bezel and the hole will be big enogh to come straight off with the door panel. See the picture below. This is the only diagram supplied in the service manual. It shows the bezel for the driver's door but it states that the rear door is similar. If you allready have the bezel off, or you are not talking about the door handle hinge, I don't know what you are talking about when you say "hinge thing"

yadayada · Answer 5 · 11/21/2016 12:00:00 AM

yadayada

78254 Answers

SOURCE: Resetting Honeywell HRDP8D500 password... Help needed... Bought a house after owner passed away. Also removed the battery inside and had a reset button inside which restarted but didn't reset

You need to call Honeywell customer service, not sure you can override the password without their help.

Posted on Nov 21, 2016

To reset the pass word on Secustar EA/ES/EH I had to unscrew a red button near the hinge thus remove the rear housing. In doing so the black wire disconnected. Where do I connect it?

5 Suggested Answers

6ya staff

Steve Allison

fz66

dttech

yadayada

Add Your Answer

Attachments: Added items

Related Questions:

How to disconnect a BCM in a chevy colorado 2007

Remove rear seat

Neither the driver's side or pass. side windows will work. Rear windows work.

95 buick lesabre door jam button that turns dome light on and off

How do you remove the lift gate or rear hatch from my 2000 Dodge Durango? I see the bolt on the hinges but I don't know where to un plug the wiring..

2002 suburban has leak in driver side rear floor. Cannot see where water would be coming from?

I cannot find the reset button for the fuel pump. Could you tell me I can find it?

I need the factory wiring radio color codes to a mazda 626 99 es so i can hook up my new alpine deck

How do you replace the backup light bulbs on a 2001 TDI Beetle?

Rear Window Sprayer not working.

Not finding what you are looking for?

Cars & Trucks

How to disconnect a BCM in a chevy colorado 2007

Open Questions:

How often do I need to put water in the batteries and what pump do I need.also should I leave it on charge whenever it’s not in use

2003 pontiac aztec power windows do not work-new switch worked 2 days only all fuseckecked ok

2001 chevy lumina stalling and surging fix fuel filter

I got a 16kg washingmachine with no power completely dead .what do I check for fault finding

Related Topics:

Ask a Question

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

yadayada

Colin Stickland

Thomas Perkins

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

2011-dodge-journey-31045.pdf....

RENAULT CLIO 3 (2006 - 2011) - MKi +...

1997_Prtg...

To reset the pass word on Secustar EA/ES/EH I had to unscrew a red button near the hinge thus remove the rear housing. In doing so the black wire disconnected. Where do I connect it?

5 Suggested Answers

6ya staff

Steve Allison

fz66

dttech

yadayada

Add Your Answer

Attachments: Added items

Related Questions:

How to disconnect a BCM in a chevy colorado 2007

Remove rear seat

Neither the driver's side or pass. side windows will work. Rear windows work.

95 buick lesabre door jam button that turns dome light on and off

How do you remove the lift gate or rear hatch from my 2000 Dodge Durango? I see the bolt on the hinges but I don't know where to un plug the wiring..

2002 suburban has leak in driver side rear floor. Cannot see where water would be coming from?

I cannot find the reset button for the fuel pump. Could you tell me I can find it?

I need the factory wiring radio color codes to a mazda 626 99 es so i can hook up my new alpine deck

How do you replace the backup light bulbs on a 2001 TDI Beetle?

Rear Window Sprayer not working.

Not finding what you are looking for?

Cars & Trucks

How to disconnect a BCM in a chevy colorado 2007

Open Questions:

How often do I need to put water in the batteries and what pump do I need.also should I leave it on charge whenever it’s not in use

2003 pontiac aztec power windows do not work-new switch worked 2 days only all fuseckecked ok

2001 chevy lumina stalling and surging fix fuel filter

I got a 16kg washingmachine with no power completely dead .what do I check for fault finding

Related Topics:

Ask a Question

Popular Questions

2003 no low bwa=eam or running light..bulbs and

Overdrive off light flashing

ABS light stays on

Toyota dashboard CD player won't eject

VTEC System Malfunction code P1259

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

yadayada

Colin Stickland

Thomas Perkins

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

2011-dodge-journey-31045.pdf....

RENAULT CLIO 3 (2006 - 2011) - MKi +...

1997_Prtg...