Question about Cars & Trucks

Open Question

P0045. Could someone please tell me the location on engine of boost control solenoid (not shift) . For Hino 700

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: jeep codes location of unit

Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.

Posted on Nov 19, 2008

  • 22306 Answers

SOURCE: shift solenoid

sorry only manuals sold in spain,havent a clue

Posted on Dec 12, 2008

  • 142 Answers

SOURCE: What does code P0753 Shift Solenoid mean?

P0753 means your powertrain computer detects a continuous open, short to ground or short to power in the circuit to your transmission's 1-2 shift solenoid. When the code is active, your transmission runs in a fail safe/limp home mode that only lets certain gear ratios function in the transmission.

The solenoid in your application looks like this
1edc2e6.jpg and it is located sometimes on the side of the transmission, but my guess is from the looks of it, it might be found inside the transmission, only accessible with the oil pan removed.
The problem might be the solenoid itself, or the wiring going to the solenoid from the computer that controls the transmission, or the computer itself.

Posted on Sep 09, 2009

  • 333 Answers

SOURCE: Pressure Control Solenoid D electrical fault (P2716)

There is a Bulletin on this concern, and it is a warrantable condition for 8 years or 80,000 miles so you are still covered by the factory warranty.
The problem is a logic issue in the PCM. The correction is a new PCM with updated software.

Reference bulletin #TC015-07

The contents are below:

TC015-07 Title:
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007

Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored.
Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring.

Applicable Vehicles
^ 2005 - 2007 model year Corolla and Matrix (2WD) vehicles equipped with the 1ZZ-FE engine.
Warranty Information
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date.

** Please be sure to rate me if this free information has been helpful!

Posted on Sep 21, 2009

Testimonial: "Thank you so much!! "

  • 11 Answers

SOURCE: where is the shift control 2-3 solenoid located on a 1996

shift solenoids are located inside the transmission. The easiest way to get to them, is to remove the drivers side front tire, and CV axle. There will be a square aluminum cover right there. IF you remove this cover, all the solenoids will be right there.

Posted on Nov 15, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

P0045 code what does the mean. 2008hyndai sante fe

code p 0045 refers to turbo/supercharger boost control solenoid---circuit open===causes ---wiring---boost control solenoid

Oct 12, 2016 | 2008 Hyundai Santa Fe GLS

1 Answer

Hino 700 engine went off while driving and wont start. What could be the problem

the reasons can be crank/cam shaft position sensor/s --wiring to sensors
fuel pressure to injectors too low---fuel pump
ignition /pump stop control solenoid
blocked tank vent ---pump staving from the vacuum in the tank
failed fuel line allowing air into pump
have a service dealer read the fault codes to get a better diagnosis and quote

Aug 30, 2016 | Cars & Trucks

1 Answer

What may cause code P0045 to appear in a no4c toyota dyna

DTC Description: Turbocharger / Supercharger Boost Control (Solenoid A) Circuit / Open

May 06, 2016 | Toyota Cars & Trucks

2 Answers

How will I fix my Toyota Hino SO5C engine,when I cranked the engine,it cranks but never starts?

first thing is to run the fault codes to determine where the fault could be
it may be a simple flat battery in the fob key that is not signalling the immobilizer system or air in the fuel system if diesel or the fuel shut off solenoid not working

Oct 11, 2015 | Toyota Cars & Trucks

1 Answer

I have an 2008 Hyundai elantra and get code 700& 760 what that mean?

Code 700 is a generic code that means a problem has occured with the transmission control module, and code 760 is for a shift solenoid failure.
The shop would use a repair manual to test the circuit for the shift solenoid. If the solenoid is faulty, it would need to be replaced and the module reset.

Sep 03, 2015 | 2008 Hyundai Elantra

1 Answer

P00A B/1 Com1 ; p00P B/1 Com2

code p0045 refers to turbo/super charger boost control solenoid---circuit open causes ==wiring--boost control solenoid
p0046 refers to turbo/ super charger boost control solenoid--circuit range/ performance===causes ---wiring---boost control solenoid ---mechanical fault.
code refers to system voltage --low===causes wiring---poor connection---battery---alternator
it also refers to ECM power relay control--circuit open===causes -wiring --- ECM relay.
looks like 2 boost solenoids and I would ensure that the battery posts and terminals are shiny clean and tight. have a load test done on the battery to check for bad cell and check the alternator drive belt for condition and tension . Have an out put test done by an accredited auto electrician on the alternator

Dec 31, 2013 | 2008 Dodge Avenger

1 Answer

2001 saturn code po500 , b0045, b0040

p0040 is Oxygen sensor signals swapped Bank 1 sensor 1/Bank 2 sensor 1.
p0045 is Turbo/ Supercharger Boost control solenoid circuit open.
p0500 is vehicle speed sensor A.

Sep 25, 2011 | 1999 Saturn SL

1 Answer

Transmission trouble

Are you inquiring about the shift solenoid to change gears internally or to shift the vehicle out of park?

May 18, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Check engine light on. Mechanic says its the

The shift solenoid is located under the side pan of the transmission. It's not a easy job to take the side pan off. May cost $700 for part and labor(both including).

Mar 11, 2010 | 2006 Ford Taurus

1 Answer

1993 mitsi lancer 4g93t cd5a, installing manual boost controller

I'm not too sure if those are setup like the Eclipse turbo engines, but those cars came stock with a BCS(boost control solenoid). That solenoid maintained the stock boost on those cars. In the eclipses, you would have to leave the electrical part of that solenoid connected, yet remove the vaccuum hoses to install a boost controller.

I really hate hot linking to other URLs, but I think this guide will help you out a lot.

Boost Controller Installation

Apr 04, 2009 | Mitsubishi Lancer Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides