Question about Cars & Trucks

Open Question

I need help for applying for training to be a solider

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you program the garage door buttons in a 2009 Porsche 911


The control is made by HomeLink. You can find instructions on how to program your specific type of garage door here:

http://www.homelink.com/program

Here are the basic steps for a "Genie" garage door opener:

  1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash, which may take up to 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)
  2. Press the appropriate HomeLink button I, II or III which you want to train and keep holding it until the indicator light starts flashing slowly. Once the indicator light starts flashing slowly, you may release the button. HomeLink is now in "training mode."You will now have 5 minutes to train your hand-held transmitter to the HomeLink transmitter in the bumper.
  3. Stand in front of your vehicle with the original hand-held transmitter for the garage door opener (or other device) that you wish to train.The transmitter unit to be trained is located in the bumper about 4 inches to the left of the vehicle's center.
  4. Hold the original hand-held transmitter between 0-12 inches from your car's bumper. NOTE: The distance between the hand-held transmitter and the HomeLink transmitter unit in the bumper depends on the system being trained. It may require several attempts at different distances in order to pick up the signal.
  5. Now press and hold the button on your original garage door transmitter while keeping your fog lights in view. The fog lights will blink three times to indicate that the training has been successful.NOTE: If the training time exceeds the five minutes, the fog lights blink once. If this happens, you should repeat steps 2 to 5.
  6. Press and hold the trained HomeLink button and observe the indicator light.
    • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
    • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with Steps 7-9 for a rolling code device. A second person may make the following steps easier. Please use a ladder or other device; do not stand on your vehicle to perform the next steps.
  7. At the receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener's manual.
  8. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, you have approximately 30 seconds to initiate the next step.
  9. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.

Jan 14, 2013 | 2008 Porsche 911

1 Answer

How to make solid lifters


Cut/machine them from a hardenable billet and make sure to provide oiling to the valve train to accomodate the changes to the oiling gallery dynamics with the switch. Plus you need to have adjustability in the valve train to maintain safe operating clearances of the valve train.

Depending on the engine, solid lifters may already be available from various manufacturers who produce solid lifter racing cams. Like Melling, Crane, Crower, etc.

Some engines such as the old flathead V8 Fords were solid lifter the entire time.

Apr 06, 2012 | Ford Mondeo Cars & Trucks

1 Answer

I have a 2005 scion xb, I have replaced brake pads and master cylinder, I've bled and bled the brakes, but foot petal still goes to floor, have nothing leaking either, help


Hello and welcome to FixYa!

When you open be bleed valve, does the fluid flow solid when brakes are applied? If yes then the problem will be on the hydrovac. You can have a vacuum leak that's why the brake pedal stays on the floor. If the fluid is not solid then you'll need to bleed it out some more. You may need to replace the hydrovac to get your brakes working normally again.

Hope this helps and thank you for using FixYa! Have a good one!

Apr 23, 2011 | 2005 Scion xB

1 Answer

Left turn arrow on solid when applying brake 2002 LW300


you have a bad bulb on the left side could be front or rear thats what they do when a bulb is bad

Feb 01, 2010 | 2002 Saturn L-Series

1 Answer

2005 hyundai accent 1.6L. car won't start


Hyundai TSB 08-BE-012

PROCEDURE:
1. For first time training, press and hold the two outer HomeLink buttons, releasing
only when the HomeLink indicator light begins to flash after 20 seconds.
NOTE: Do not perform this step when training the additional HomeLink buttons.
2. Position the hand-held transmitter 1-3 inches away from the HomeLink mirror,
keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button
and the hand held transmitter button.
DO NOT release until the HomeLink indicator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both buttons may be released. The rapid
flashing indicates successful training and the procedure is complete. This also
indicates that the garage door opener does not use rolling code technology.
Note: The garage door may open or close during this step.
Steps 4 through 7 are only necessary if the HomeLink button appears to be
transmitting after step 3, but the garage door does not operate.
4. Press and hold the trained HomeLink button and observe the indicator light.
If the indicator light is solid/continuous, training is complete and your device should
activate when the HomeLink button is pressed and released.
If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light,
proceed with the following training instructions for a rolling code device. A second
person may make the following steps quicker and easier. It is recommended that a
ladder or similar device be used to obtain access to the motor housing. Do not stand
on the vehicle to perform the next steps.
5. At the garage door opener receiver (motor housing) in the garage, locate the “learn”
or “smart” button (usually near the hanging antenna wire attached to the unit). If
there is difficulty locating the training button, refer to the garage door opener’s
manual.
6. Press and release the “learn” or “smart” button (the name and color of the button
may vary by manufacturer).
NOTE: Once the button is pressed, there are 30 seconds in which to initiate the
next step.

7. Return to the vehicle and firmly press and hold the trained HomeLink button for two
seconds and release. Repeat the “press/hold/release” sequence up to 3 times to
complete the training process. If successful, your garage door should open or close
during this step.
If the vehicle owner continues to have difficulty programming their HomeLink mirror,
please have them contact HomeLink customer service directly at 1-800-355-3515 or
www.homelink.com for further assistance.
PROCEDURE COMPLETE

Good luck!

Dec 06, 2009 | 2005 Hyundai Accent

2 Answers

How do I setup the homelink feature in my 2000 chevy impala with my garage opener?


First clear it pushing the 2 outer buttons for about 20 seconds till the lite blinks.
Then here is the weird part take the old remote that you use for your garage door opener and hold it next to the home link in the car.
Push the button on your old remote then the button on the home link. the home link will flash slow then quickly (about 10 sec).
Now go push the learn button on the main door unit then back to the car and push the home link again for 2 seconds.

Oct 22, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

1997 toyota conquest 1.8. Turn indicators are scrambled.


Have a look at your relay and fuses. But you may not apply DIY method because this needs an expert hands-on. Needs to trace where the wires were wrongly connected.

Rate this please.

Apr 04, 2009 | 2006 Toyota Corolla

1 Answer

Jag xj6 1996 97 programming the garage door openers


1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.) 2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your visor), keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)
property_damage_symbol_sm.gif Note: Some garage door openers may require you to replace step 3 with the “cycling” procedure noted in the “View Canadian Instructions” section.
4. Press and hold the trained HomeLink button and observe the indicator light.
  • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
  • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener’s manual or contact us. 6. Press and release the “learn” or “smart” button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, there are 30 seconds in which to initiate the next step. 7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the “press/hold/release” sequence up to 3 times to complete the training process.

Jun 13, 2008 | 1997 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...