Question about Nissan Cars & Trucks

Open Question

Nissan z24 engine just did head gasket replaced timing chain and guides started on oil pressure pulled off new oil filter no oil primed pump on bench before installing can you help , no oil

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mecanica03
  • 881 Answers

SOURCE: Nissan Timing Chain still rattling

and the lower chain guides?

Posted on Apr 20, 2009

  • 143 Answers

SOURCE: head gasket failure on Nissan Pathfinder

the head needs to be checked by a reconditioner if all is good a complete cooling system check needs to be carried out. Coolant type, mix and flow all need to be considered. all leaks need to be fixed, i would renew all cooling system componets. Thermostat, all the way up to the heater core(inside the vehicle used for the internal heating of the vehicle) at the extreme. This repair job may be costly, ONCE more info pls

Posted on Jun 13, 2010

  • 2 Answers

SOURCE: My bmw e34 89 model with the m20 engine ,had

what oil is recommended foe bmw e34 with m20 engine?

Posted on Jul 14, 2010

  • 2309 Answers

SOURCE: I have a 1996 Chevy C1500 5.0L Vortec V8. I lost

next step is to remove the intake, you are on the right track, worse i ever found was a cracke block, but that was in a 61 t-bird which was repaired with jb weld ten yrs ago and still holding, but the intake gasket sounds right

Posted on Jul 19, 2010

  • 5280 Answers

SOURCE: fuel pump won't run unless engine is cranking, but won't start

Are you sure it's running when cranking? It should have come on when key turned on.
This is for camrys up to year '91. It may apply in your '95, also. Check the 7.5 amp ignition fuse and the 15 amp EFI fuse and the EFI main relay, all located in the fuse box next to your battery. There is also the circuit opening relay tied in to fuel pump operation. It is usually found under center of dash. It is usually not the problem, but it is part of the checks for fuel pump operation.
If your car has a " check connector" or "service connector" (also called a fuel pump check connector) under hood on driver's side near the firewall (a little 1 inch cube with a cap on it), then bridge terminals +B and Fp with a jumper wire. Turn key to on (don't start car). The pump should come on. Listen for fuel return noise from the fuel pressure regulator, and verify pressure in hose from the fuel filter. If nothing, check those fuses above. Here is how power runs to pump: Battery to 40 amp main fusible link-to 15 amp EFI fuse-to EFI main relay-to circuit opening relay-to fuel pump-to ground. Ignition switch and the computer (ECU) work the relays to pass power to pump. Hope this helps some, Randy. Good luck.

Posted on Nov 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan z24 engine just did head gasket replaced timing chain and guides started on oil pressure pulled off new oil filter no oil primed pump on bench before installing can you help


os there something in the repair manual
about the Z24 oil pump cam being in alignment

Remove the distributor by removing the two mounting bolts to the timing cover. This will keep your ignition timing intact. Fit the oil pump and drive spindle together and install so that when you look down on top of them the spindle is aligned like below.


index-av0lfw4mhtvzatxb1mcuht3e-5-0_1.jpg2008-10-26_052041_shot0178-av0lfw4mhtvzatxb1mcuht3e-5-2.jpg

Apr 17, 2017 | Nissan Cars & Trucks

1 Answer

I NEED TIMING CHAIN DIAGRAM FOR VQ20 NISSAN SERFIRO 1999


Instructions
  1. Remove Your Timing Chain
    • 1 Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Altima is 60,000 miles.
    • 2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.
    • 3 Drain the cooling system and disengage the negative battery cable. Undo the spark plug wires and set the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.
    • 4 Disconnect the engine undercover, vacuum and fuel hoses, harness and connectors, drive belts, power steering reservoir, alternator and bracket, upper radiator hose, air duct, front exhaust tube, intake manifold collector supports, collector and exhaust manifold and the distributor.
    • 5 Prop up the oil pan and take out the front engine mounting, the valve cover, camshaft sprockets, cam bearing caps, camshafts, cylinder head bolts (reverse the installation order), cam sprocket cover, upper chain tensioner, chain guides and chain, idler sprocket bolt, cylinder head, intake manifold and cylinder head gasket and the steel oil pan.
    • 6 Place a steel cutter between the steel and aluminum oil pans. Slip the cutter around the oil pan's edge. Disengage the steel oil pan, baffle plate, oil strainer and the front tube.
    • 7 Secure the car on jack stands and place a seal cutter in between the oil pan and cylinder block. Slip the cutter around the oil pan's edge.
    Install Your Timing Chain
    • 8 Reconnect the crankshaft sprocket, oil pump drive spacer, idler sprocket and lower timing chain. Position the lower timing chain on the sprockets and line up the mating marks.
    • 9 Rub on an unbroken bead of liquid gasket and put in a new front cover and oil seal. Secure the bolt at 105 to 112 foot pounds (142 to 152 Nm).
    • 10 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.
    • 11 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.
    • 12 Refill the cooling system and add clean oil in the engine.
    • 13 Hook up the negative battery cable and any other disconnected parts or items. Start the engine and look for leaks.
Tips & Warnings
  • Procedures for replacing timing chains in Nissan Altimas vary slightly depending on engine size.
  • Make sure the new timing chain matches the chain you are removing.

Jun 12, 2012 | Cars & Trucks

1 Answer

2006 nissan frontier low oil pressure at idle after timing chain replacement


I have just spent $1500.00 to fix this low oil pressure problem. The main cost was having the timing chain replaced and where the oil pressure problem was found. The low oil pressure problem is caused by a bad gasket that is under a plate inside the timing chain cover. The dealer wanted to replace the whole housing as Nissan dose not offer a new gasket and wants you to replace the inner timing chain housing. The plate covers part of the oil gallery, the gasket breaks out from this plate and that is where the oil pressure goes. The gasket can be replaced by removing the plate and making a new gasket. Note getting to the plate inside the timing cover is a major labor issue that takes about 12 hours to complete start to finish. I had to fabricate the gasket my self as the dealer would not. Cost for fixing the bad gasket was about $17.00 for materials. Replacing the timing chain was at my request as it was making noise.

Jan 27, 2012 | Cars & Trucks

1 Answer

Timing chain 96 maxima broke


Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Maxima is 60,000 miles.2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.3 Release the pressure in the fuel system, drain the cooling system and disengage the negative battery cable. 4 Undo the upper radiator hose, engine drive belts, power steering pulley and pump with bracket, air duct, passenger front wheel and engine side and undercovers, front exhaust pipe, cylinder head front mounting bracket and head cover, rocker cover, distributor and distributor cap and spark plugs.5 Take off the intake manifold support and move the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.6 Disconnect the cylinder head front cover, water pump pulley, thermostat housing, upper and lower tensioner and slack side timing chain guide, idler sprocket bolt, camshaft sprocket bolts, sprockets, mounting caps and camshafts. 7 Disengage the cylinder head with the manifolds, idler sprocket shaft, upper timing chain, center crossmember, oil pan and strainer assembly, crankshaft pulley, engine front mount and bracket and the front timing cover. Remove the oil seal and unfasten the timing chain cover, idler and crankshaft sprockets and the oil pump drive spacer. 8 Unfasten the timing chain guide. install Your Timing Chain 1 Grease the oil seal lip with engine oil and place it in the front cover. Verify that the No. 1 piston is at "Top Dead Center" (TDC) of the compression stroke. 2 Reconnect the crankshaft sprocket (marks should point toward the engine's front), oil pump drive spacer and timing chain guide and the lower timing chain. Line up all mating marks.3 Hook up the crankshaft sprocket and pulley, lower timing chain, front cover assembly, engine mount and front mounting bracket, oil strainer and pan assembly and center crossmember.4 Reattach the upper timing chain, idler sprocket (to the back side), cylinder head assembly, idler sprocket bolt and exhaust and intake camshafts. Place the intake camshaft knock pin at 9 o'clock and the exhaust pin at noon. Connect the camshaft bearing caps and distributor brackets and secure all mounting bolts.5 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.6 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.7 Refill the cooling system. Hook up the negative battery cable and any other disconnected items. Start the engine and look for leaks.

Oct 14, 2011 | 1996 Nissan Maxima

1 Answer

Just replaced timing chain, guids, gears and tesioner in a 1991 nissan pickup with a z24 engine and still has a rattle when it worms up, not there when its cold would it be low oil pressure


Sounds like oil pressure.Try thicker oil and if the problem presists than
Check tension on chain and rotate by hand to see if everything lines up and there is no slack /
when installing oil pump ,ensure the oil ports line up/
check oil pressure with gauge

Apr 16, 2011 | Nissan Pickup Cars & Trucks

3 Answers

My 04 XTerra's oil light keeps coming on but there is oil in the car....not overheating, driving okay??? I am perplexed.


1st you need to do an oil pressure test. If it reads between 20psi-60psi, then it's Ok and you have a bad oil pressure switch. If it's below the above specs then you have an internal engine problem - IE: bad oil pump, bad bearing, etc...

Mar 12, 2011 | 2004 Nissan XTerra

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

2 Answers

Oil not circulating ? 1999 Nissan Altima DOHC, KA24DE, 200315 miles The right side guide rail to the lower timing chain shattered and jammed the oil pump. I have replaced the oil pump and both timing chain...


Well, from the oil pump it goes into your oil filter so the lines going from the pump into the filter could be clogged. check that and see. Also on most imports I have found that they have to be primed after the oil pump has been replaced. Buy a oil pressure gauge and hook it up. Disconnect your fuel and spark delivery and then just crank over your motor to make sure you have good pressure. It takes up to 30 seconds to build on some cars. hope that helps.

Jul 21, 2009 | 1999 Nissan Altima

1 Answer

Serious timing issues on 1985 nissan king cab z24.


Hi,did you get your 720 fixed,I also have a 85,Ii replaced my engine with a Jasper engine,if you still need help let me know,here's a video of mine. 85 Nissan 720 4x4 2 4 Weber conversion

Apr 18, 2017 | 1985 Nissan King Cab

1 Answer

Timing chain


I'll assume you are going to replace the entire set (sprockets, guides, etc.) which I got from O'Reilly for $79.

First, set engine to #1 TDC.
Remove valve cover, fan shroud, fan, drive belt, water pump, 4 10mm bolts from bottom front of head, and 3 10mm bolts from front of oil pan. Remove lower front shield to remove oil pump. remove oil pump/distributor drive shaft, noting the orientation of the drive shaft.
Remove harmonic balance using correct puller (can be rented from local auto parts store). Remove P/S pump and A/C compressor if necessary. Remove timing cover.

IMPORTANT: Before removing oil thrower and distributor drive gear, note direction of oil thrower.
Remove oil thrower and distributor drive gear.
Remove chain guides, tensioner, chain, and finally both sprockets.
The new crank sprocket can only be installed one way, by aligning groove with keyway. The new cam sprocket will have 3 guide holes on the mounting flange, and you will need to align the knock pin with hole #2. Both sprockets should have a small dot (timing mark) on the right side of the sprocket when viewed from the front.
To install new chain, inspect chain to find the two brightly colored gold links. These two links must align with the timing marks on the sprockets. Assemble and install chain tensioner.

!!! IMPORTANT: Be sure to use new gasket when installing tensioner. Tensioner is oil pressure fed and a leaking gasket could allow chain slack, leading to premature wear or break.
Install chain guides, being sure not to let tensioner pop out.

!!! IMPORTANT: The tensioner must be fully compressed. To accomplish this, loosen the 8mm bolts in the passenger side guide (the shorter one). Compress the tensioner, adjust guide to remove slack, and tighten the two 8mm bolts.
Double check that everything is still lined up properly, and make corrections as necessary.
Install distributor drive gear and oil thrower.

!!! IMPORTANT: Ensure oil thrower is installed facing away from the distributor gear. If not, it could get caught in the distributor gear and destroy the two gears or cause engine lockup.

Before installing timing cover, inspect coolant and oil passages. If there is excessive buildup, a good system cleaner is recommended. Replace timing cover gaskets to prevent oil leakage. The best way to reinstall the timing cover is to remove the oil pan, install the timing cover, and reinstall the oil pan (replacing the pan gasket). If you don't want to do that, simply grease the top and bottom of the timing cover and lightly tap it into place with a rubber mallet. This is to prevent damage to the oil pan and head gaskets.
To install the distributor drive shaft, dab some grease on the top side of the gear to hold it in place, and line it up with the distributor. If you are having trouble lining up the shaft, pull it out and look at it from the top, and you will see that the flange is offset. At #1 TDC, the offset will be towards the front.
Install oil pump, being sure to use new gasket.

!!! IMPORTANT: Failure to replace oil pump gasket could lead to inadequate oil pressure, which will cause severe engine damage.

The remainder of the installation is a reverse of removal, using new gaskets where necessary. Before installing your valve cover is a good time to check your rocker arm clearances. This is also a good time to replace your drivebelt, and any other maintenance items as necessary.

Sep 11, 2008 | 1986 Nissan King Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...