Question about Cars & Trucks

Open Question

My clips to my overhead console switch panel broke

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removal of 2002 f350 overhead display?? Much different than exploder


if you are sure there are no screws , its held in place by spring clips . just pull it down carefully and use a panel remover

Feb 28, 2014 | Cars & Trucks

1 Answer

Changing the interior map light


The bulbs is replaced from the back of the overhead console with 1/4 turn bulb holders.

the overhead console ( non rail version ) is held up with spring clips.

Open the rear compartment, and grab the rear corners and pull down 1 at a time. They are very hard to pull the 1st few times. Once you have the read released, there is another set of spring clips in the front, so be careful how far down you pull the rear, until the front is released.

Once you can see the back of the overhead console, you will see the 1/4 turn bulb holders for the map and interior lights.

Sep 18, 2011 | 2005 Ford F-150

1 Answer

How do you remove the overhead console in a 2000 expedition?


  1. Remove the screw from the inside of the sunglass storage bin.
  2. Release the three clips and slide the roof console forward and then down. (pull down to release clips).
  3. Disconnect the electrical connectors.
This will remove the main overhead console. Good luck.

Apr 05, 2011 | 2000 Ford Expedition

1 Answer

Replacing the front dome light


The front dome lamp & map lamps are replaced from the back, they are 1/4 turn bulb holders.

The overhead console ( non rail ) is held on with spring clips. Open the rear compartment, and in each corner grab the console with your thumb and index finger and pull down. The 1st time you remove it, it is very hard to pull down, the springs are very stiff.

The rail system, the service manual says to pull the overhead bins 1st, then pull the consoles out ( also spring clips )

Feb 19, 2011 | 2006 Ford F-150

1 Answer

Sun roof will not close on 02 f150


Best to start by testing the motor.

Pull down the overhead console ( spring clips, and a screw to the front is how my 2001 was mounted, but it did not have the roof panel opening, could be all spring clips ), remove the power roof panel switch connector, and apply power to the leads to the motor.

The motor is the Blue & Violet wires from the roof opening panel module.

If this tests good, next is to test the switch.

The common wire to the switch is the Brown w/ Orange stripe wire, the Close tilt up is the Tan w/ Red stripe wire and the open / Tilt down is the White w/ Red stripe wire.

Sep 21, 2010 | 2002 Ford F150 Regular Cab

1 Answer

I need to take display panel for temp and compass out to check connection, 2001 f 150 super crew lariat sunroof


Could be 1 of 2 types.
1st type has a single crew in the bottom of the overhead console, with a screw in it, and spring clips towards the display.
2nd type is held on with spring clips only, they are hard to pull out the 1st time.
Check which type you have.
The display, chances are the display has had one of the resistors come loose, these are 51 ohm resistors, and could just have 1 side that came unsoldered, or could be missing all together.
This is what the SuperDuty overhead console looks like when the resistors are missing ( these are 68 phm resistors, different than the F-150 ), to give you an idea of what to look for.
faadd21.jpg

Sep 10, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

How do I remove the overhead console in my Ford 1-50 to change a light bulb. I ordered the bulb from the Ford house, but they want a small fortune to replace the bulb


With the overhead console ( non rail system ), open the sun glass bin, and grab each corner in the back, and pull down.

The overhead is held on with 4 or 6 spring clips, and pulls straight down.

The bulbs are 1/4 twist sockets installed from the back of the overhead console.

May 17, 2010 | 2006 Ford F-150

1 Answer

My sunroof is not able to be closed. It is in the pop up position. Is there a manual way to close it? eg no use of electricity?


there is no manual method. It sounds like a limit switch is not working. Can you hear the motor try to operate? If you push up on the back of the glass a little bit while hitting the switch, what happens.

go here for villager help

http://groups.yahoo.com/group/villagerquest/


The sliding roof panel system consists of the following components:
  • RH circuit breaker
  • Timer module
  • Power window relay
  • Roof sliding panel switch (15B691)
  • Roof glass panel (50054)
  • Sliding roof panel motor (15790)
  • Halo moulding
  • Roof sliding panel headlining (519A02)
  • Roof sliding panel slide links (502M78)
  • Roof sliding panel housing (502C22)
  • Roof air deflector (500A26)
  • Center green diode strip
-------------------------------------
When the roof sliding panel switch is activated, a gear on the sliding roof panel motor drives a spline on the roof sliding panel housing. Within the roof sliding panel housing, the spline is connected to two sliding roof panel cables which cause the roof sliding panel slide links to slide and the roof glass panel to open or to close. The sliding roof panel cables and the spline are part of the roof sliding panel housing. Neither the sliding roof panel motor nor the roof sliding panel housing can be disassembled. If a malfunction is detected with either of these assemblies, the assembly must be replaced.
----------------------------------------------------------------------------
VISUAL INSPECTION CHART Mechanical Electrical
  • Damaged sliding roof panel
  • Sliding roof panel height adjustment
  • Sliding roof panel fore and aft adjustment
  • Blown fuse(s):
    • 30A PWR WDW
  • Damaged circuit breaker #1
  • Damaged wiring harness
  • Loose or corroded connections

------------------------
  • Sliding Roof Panel Does Not Open or Close
  • Fuses.
  • Circuit breaker #2.
  • Power window relay.
  • Sliding roof panel motor.
  • Roof sliding panel switch.
  • Circuit.
  • GO to Pinpoint Test E1 .
  • Sliding Roof Panel Will Not Stop in Vent Position
  • Sliding roof panel motor.


Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Gently pry the overhead console from the headliner.
  1. Disconnect the sliding roof panel electrical connector from the overhead console.
  1. Disconnect the rear quarter window switch electrical connector from the overhead console, if equipped.
  1. Disconnect the map lamp electrical connector from the overhead console.
  1. Remove the overhead console.
  1. Remove the two roof sliding panel switch screws and the roof sliding panel switch (15B691).
--------------------------------------------------------------------------------
Motor Removal
  1. Place the roof glass panel (50054) in the closed position.
  1. Remove the roof headlining (51916). Refer to Section 01-05 for the removal procedure.
  1. Remove the two sliding roof panel relays from their brackets.




  1. Disconnect the two sliding roof panel motor electrical connectors.
  1. Remove the two sliding roof panel motor screws and the sliding roof panel motor (15790

Jan 11, 2010 | 1997 Mercury Villager

1 Answer

HOW DO YOU REMOVE FRONT DOME-MAP LIGHT HOUSING


For the non rail system overhead console :

There are spring clips holding the console to the roof.

Open the compartment, and grasp each corner, and pull down. This will take a moderate amount of pull to release the spring clips.

There are 4 or 6 spring clips holding the console to the ceiling, at the least the center spring clips will release when you pull down on the rear.
remove the front held in place by the spring clips. There are 2 connectors for the overhead console, these have ~ 6" if slack in them.

From this point, you can remove the connectors, or you will see the gray bulb holders for the map / interior lamps. These are 1/4 twist bulb holders.

Nov 06, 2009 | 2004 Ford F150

1 Answer

My 2001 Mercury Cougar moonroof is stuck, it opened a few inches then just stopped. Is there a way I can manually close it?


Check fuses #21 40 amp check relay jump 12 volts to motor circuit
Overhead Console Removal
  1. Disconnect the battery ground cable.
  1. NOTE: Remove the interior lamp as a unit.
    Ease out the interior lamp.
    • Disconnect the electrical connectors.
    v4301245.jpg
  1. Remove the overhead console screws.
    v4301246.jpg
  1. Remove the overhead console.
    • Apply an even downwards force to both sides of the console.
    • Disconnect the roof opening panel switch electrical connector (if equipped).
    • Disconnect the information and message center electrical connector (if equipped)
-----------------------------------------------------
SECTION 501-17: Roof Opening Panel 2001 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/8/2001
Roof Opening Panel Motor Removal
  1. Remove the overhead console. For additional information, refer to Section 501-12.
  1. Disconnect the sliding roof motor electrical connector.
    v4101317.jpg
  1. Disconnect the sliding roof panel relay.
    v4101318.jpg
  1. Remove the sliding roof motor control unit.
    v4101322.jpg
Installation
  1. To install, reverse the removal procedure.

Oct 30, 2009 | 2001 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...