Question about Cars & Trucks

Open Question

Have a jlg 45 manlift...boom raise but will not lower

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replace 2007 dodge dakota tront shocks from strut spring assembly


Hello Russell,

If you replacing the front struts as an assembly the springs will be equipped and ready to install.

If your purchasing the strut assembly without the coil springs you will need a spring compressor.

  1. Before servicing the vehicle a service manual for safety precautions should be consulted.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove the upper shock nuts.
  6. Remove the stabilizer link lower nut and then separate the stabilizer link from the lower control arm to gain access to the lower shock bolt.
  7. Remove the lower shock bolt.
  8. Remove the shock.
To install:
  1. Install the upper part of the shock into the frame bracket.
  2. Install the nuts. Tighten to 45 ft. lbs. (61 Nm).
  3. Install the lower part of the shock into the lower control arm. Tighten the bolt to 155 ft. lbs. (210 Nm).
  4. Install the stabilizer link lower nut to the lower control arm.
  5. Remove the support from the lower control arm outboard end.
  6. Install the tire and wheel assembly.
  7. Remove the support and lower the vehicle.

Jul 27, 2016 | Dodge Cars & Trucks

1 Answer

The dig boom will not raise or lower on a 1020 walk behind trencher


Craig, I do not have a lot of experience with trenchers, if hydraulic operated not enough oil/check reservoir,, one of the valves/controls may be stuck, you will have to follow line from boom cylinder and trace it back to the valve and dismantle and repair. Secure boom as to not harm you or others.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Apr 13, 2016 | Cars & Trucks

1 Answer

Replace cylinder in bottom boom on hiranger bucket truck


ive heard of folks doing it without a crane but i would not try it , alignment is too critical with getting guides and stops back in and with nothing to move boom that would be too difficult

anyways: suspend boom end with double straps from crane , disconnect hydraulic/electric swivels/plugs at truck end lift end of boom slightly with boom all the way extended straight out , remove acess panel (both sides) at jct of upper/lower boom section . remove C clip one side drive out pin oppisite side (wiggle boom to clear pin) locate stops in lower section boom end unbolt , slowly pull upper boom with crane away take care of hydraulic lines and electric wires set on floor on wood cribbing , locate bottom of cylinder truck end find C clip and pin Might be behind a trim cover that might need to be remove drive out pin also remove bottom cylinder hyd hose connect crane to cylinder end move out a foot or so remove top cyliinder hydraulic hose then carefully slide out cylinider with crane , Note if your valves are not tight and new oil will leak back and cause boom base to sag when you unhook hydraulic hoses , your gonna need to block this up with wood cribbing just in case

reverse removal process to install new one , also i would not just install a new seal (you can) with out having cylinder recromed I'll bet it's rusty thats what tears the seals up
and allways replace entire oil volume in hydraulics your old seal is in old oil not good for the new one

Apr 26, 2014 | 1985 Chevrolet Chevy

1 Answer

My excavator hitachi ex200-1 weak swing and when you swing then stop vibration begin on turn table when i stop to swing,and when i swing and lift cylinder raise,vibration on the turn table will contin


Not sure would need to have a good look ,but i suspect a safety valve isnt closing properly causing thumping within the hydraulic system which is the vibration you can feel,shouldnt cost a lot to repair providing the faulty valve can be located so return to the dealer as they will have a good idea as yours isnt the first to go wrong iam sure

Sep 24, 2012 | Cars & Trucks

1 Answer

Wiring diagram for genie tz 34/20 manlift


INCORRECT PRODUCT CATEGORY

I'm sorry but you have this posted in the wrong product category. Please re-post the question in the proper category This is the car and truck problem category



Jun 26, 2012 | Cars & Trucks

1 Answer

The Driver side window on my 2000 Buick Park Avenue will not go all the way up. It started making this strange noise when I would lower and raise the window, but now it is stuck in the midway position. ...


Would have to experience window problem myself, but sounds like you may need a new power window motor and/or window sash "peanut". (must remove door to fix this problem) 45 min. job for exp. tech. Good luck,best regards.

Jan 22, 2011 | 2000 Buick Park Avenue

1 Answer

I can't get my 95 gmc tailgate to come off. I know that you usually open it alittle and it will come off. But mine will not. So I would like to know if there is a trick to taking a 95 sonoma tailgate off.


  1. Lower the tailgate to the horizontal position.
  2. Disengage the cable on the right and left sides from the striker bolts. To accomplish this, pull up on the middle of the cable assembly while raising the gate to a 45 degree angle, but be careful not to pinch the cable between the gate and bed.
  3. Remove the tailgate from the vehicle by lifting upward on the left side to separate the left hinge assembly, then disengage the right hinge.
To install:
  1. Install the gate to the vehicle by lowering the right hinge assembly into position first, then holding the gate at a 45 degree angle and seating the left hinge assembly.
  2. Engage the left and right cables to the striker bolts.
  3. Verify proper tailgate latching and operation.

Aug 07, 2010 | GMC Sonoma Cars & Trucks

1 Answer

Hub nut tourqe specs


TORQUE AT 45 FT LBS.WHILE VAN IN RAISED POSITION.WHEN LOWER ON GROUND TIGHTEN AXLE NUT WITH BRAKES APPLIED TORQUE AXLE NUT 180 FT LBS.BESURE TO REPLACE OLD COTTER PINS WITH NEW ONES.

Jun 14, 2010 | 1992 Dodge Caravan

1 Answer

How do i remove the transmission in my 95 geo prizm


This requires a boom which is a mounting brace which that holds the engine in place (from the top) as you drop the lower subframe in order to remove the transmission. Once the boom is in place and hooked to the engine,lift and remove wheels,exhaust,lower control arm,axles,subframe and finally the transmission. .

Aug 23, 2009 | 1995 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...