Question about Chrysler 300

Open Question

Howtoinstallgaspedal2006chryaler300 i m installing the gas pedal but cant get to the top right top bolt

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my G16 gas golf cart whines when the accelerator is pressed down but will eventually start after pressing it 4 or 5 times and it seems to help somewhat if I press it at the top which is odd???


yamaha g16 gas golf cart

time for a service and cant be ignored

something not right between pedal and drive wheels
if pedal has to be pressed like that

26215006-wof0kwh1xpwidkmx23mdilgp-4-0.jpg

Jun 08, 2016 | Cars & Trucks

1 Answer

My gas pedal gets hard during driving can my idle pulley cause that


Look under the hood. you should find a part under there with two metal thin lines connected to it so that when you push the gas pedal, that part moves up, when released, it should go back down, have someone press the gas pedal and look for it right on top of the engine. is there something blocking it? wiring harness, etc.?

Dec 09, 2015 | 1997 Cadillac DeVille

1 Answer

Brake pedal in s10 moves side to side, unattached somewhere under dash...how do I disassemble?


at the top of the brake pedal is a mounting bracket that holds the pedal in place,, on that mount, and the pedal, is a bushing that goes bad,, the hold down bolt goes right through it, if this bushing is bad, it will allow the pedal to move slightly from side to side, if however if your pedal has a lot of movement,, you need to check the bracket in total, follow the brake pedal up under the dash,, and check the mounting bolts

Sep 20, 2011 | 2003 Chevrolet Blazer

1 Answer

I have an issue with a 87 toyota pick up carburetor. Sometimes it doesnt want to start and sometimes it does a friend told me its that diaphram on the front of the carb with the 3 bolts but he could not...


Okay, your freind may be right, that part is called the accelerator pump, it is used for starting the truck, when you pump the gas to start it this pumps a few squirts of gas into the carb. what concerns me is that you hold the gas pedal to the floor to start it, most of the time an internal leaking carb floods the engine and holding the pedal down will let it start, a quick test would be to use a carb cleaner spray and before trying to start the truck hit the gas pedal and see if inside from the top of the carb look and see if you see a squirt of gas spray out, you will need some one to push the gas pedal or you can do it at the carb, if it squirts gas then the accelerator pump may be good and carb may be leaking and need rebuilding but if it doesnt squirt then its bad and then i want you to spray the carb cleaner into the carb and try to start the truck and if its due to the accel pump then after you spray into carb the truck should fire up and run without having to hold the pedal to the floor, if thats the case then replace accel pump if it still doesnt fire until you hold gas down then crab needs rebuilding . good day. hope this is helpful.

Apr 17, 2011 | 1987 Toyota Pickup

2 Answers

Trying to change disc brakes need help on how to do that


You need to take off the tire. Then, you need to take the two bolts off that hold the caliper up. The caliper will come off and the brake pads are inside. Pay close attention to how the old ones are in. Put the new ones in and put the caliper back on. Also, when you take the two bolts off the caliper to get to the pads, don't get the top bolt and bottom bolt confused. They won't fit right. Top is top and bottom is bottom.

Mar 05, 2011 | 2001 Ford Windstar

1 Answer

Bought a used 1996 couger and the heater core is by passed. im asumming the heat core needs replacing is it necessary to remove the entire dash my haynes manual does not say to remove it but when i follow...


1996 mercury cougar heater core replacement
we just bought a car with the same problem

http://members.tccoa.com/timb/Heatercore.htm

we did not have the bolt above the gas pedal
"1 on the tunnel above the gas pedal"

Jan 22, 2011 | 1996 Mercury Cougar XR7

1 Answer

How in the world do you change brake pads on a 2002 Town&Country


After supporting the vehicle safely.....With the wheel off you should see two bolts facing away from you near the top of each end of the caliper.
Remove these two bolts then pop the caliper up and off with a big screw driver or pry bar exposing the brake pads.
Do not remove the brake hose.
Replace pads....push caliper piston back into caliper and reinstall caliper and bolts.
Thread locker (liquid) should be applied to caliper bolts.
Caliper sliders....the parts the bolts go into .....should slide easily in calipers.
Push brake pedal a few times to restore pedal height before driving.

Aug 31, 2009 | 2002 Chrysler Town & Country

1 Answer

94 caprice v8 an i cant spin wheels (burnout) what to do


Sounds like the timing is retarded. Loosen the distributor hold down bolt and turn the distributor counter clockwise about a half inch or so. Then drive the car. If it runs better then get a timing light and set the timing to 10 to 15 degrees before top dead center (btdc) at idle with EST disabled (if equipped) or if it has a vacuum advance with vacuum hose disconnected. Good luck.

May 20, 2009 | 1994 Chevrolet Caprice Classic

2 Answers

Egr valve on a 2002 Saturn SL1


Take off air breather tube,you should see a cone shaped part, on top and at back of engine right by the gas pedal cable. Remove the 2 10mm bolts, and it should come right off.

Mar 16, 2009 | 2001 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...