Question about 2002 Chrysler PT Cruiser

1 Answer

Starter went bad lots of sparks got new one put all back right and now cranks but wont fire. have power to coil pack Brand new also the crank and cam sensor

This is on a 02 pt also before the starter it would sound like it was weak but 2 full turns and it started ran find as well. was told if crank sensor is good the rpm needle would move when you crank it over saw vid of it is this true

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 124 Answers

Yes, tacho also runs off that sensor.
I trust you disconnected the battery before you pulled the starter?
If not you may have fried a module or 2 and possibly even the computer.

Posted on Apr 17, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would be the problem if my van won't strat


check your timeing chain or belt whichever you have

Sep 17, 2014 | 2003 Chevrolet Venture Passanger

1 Answer

My bmw 1.6 e36 has lost its spark i have changed both crank and cam sensor could the lambda sensor still be the fault


Hi Thomas, You seem to have attended all that is required for the spark. Check the wiring and if it's fine I would suggest you have a diagnostic scan carried on on the vehicle. That will pinpoint the problem and allow a long term fix. Regards John

May 29, 2013 | BMW Cars & Trucks

1 Answer

So... I'm starting to get just a bit frustrated... after installing the new PCM, my dodge avenger, 96 2.0L ran for 5 days then went out again, fuel pump works and I've got spark but no start..


after all that work its terrible that something else goes bad however since you do get spark and fuel i would say crank or cam sensor but then if one of those goes bad it wont allow engine to turn over and would shut fuel pump off. so there is only one thing left to cause it you have a short in the harness somewhere maybe just a lose connection on the cam or crank sensor put dieelectric grease in all your connectors

Apr 03, 2013 | Cars & Trucks

1 Answer

2000 pontaic montana wont spark


likely a bad crank sensor or bad ignition module, coil packs can go bad
to but not normally all three at the same time.if the coil packs look ok
then i would look at what tell it to fire witch is the crank sensor, the cam sensor should tell the injectors when to fire, but thats not to say they couldn't be linked in some vehicles needing singal from both for fuel
and fire to work. hope this helps

Feb 16, 2013 | 2000 Pontiac Montana

2 Answers

It turns but it wont start,it has gas and power


Pull off the coil ignition cable at the distributor and check for spark coming out of coil when cranking engine over. Use a heavy rag or glove to hold the wire 1/4 inch from a metal ground. Should see a strong blue spark when cranking to verify ignition is good. If no spark, check for battery voltage to coil on the coil primary. If you have current to the coil, suspect a bad coil, ignition module, crank position sensor, or cam position sensor, or pcm. The coil, ignition module, and sensors can be tested before replacing.

Jan 29, 2013 | Cars & Trucks

2 Answers

1995 ford explorer doesn't start, crank & cam sensors replaced


Does you fuel pump delivers fuel. Is it there a spark.

Dec 29, 2009 | 1995 Ford Explorer

2 Answers

Car cranks but wont start. I have no power to the


well if spark quits fuel usaly will to computer will do this to stop cadilac converter from filling with fuel!and causeing a fire saftey feature!!!!okay disconect battery wait a couple of minutes reconect! turn key on postion do not start or crank!off then on until you hear a GRRRRunt that is your fuel pump that is what you should hear turn your head to the right towards back seet and once you hear it that means pump is good then crank it then spark should quit if the coil packs a r bad then you have your problem if so test for spark also if you have eng light on cut the case hook up obd 2 scan find the fault and fix THIS IS WHAT I WOULD DO CHEERS!

Dec 23, 2009 | 2003 Kia Optima

2 Answers

2001 FORD TAURUS 24 VALVE DOHC MOTOR WILL NOT START


i have a 2001 taurus 24valve dohc 3.0 engne i have a bad coil pack what steps do i need to do to change the coil pack

Sep 07, 2009 | 2001 Ford Taurus

2 Answers

I cant get spark out of the coil pack


cam sensor fires the injectors to synchronise injector pulsing with the spark at the spark plugs.. U need to probably change the crankshaft sensor (around the crank pulley) as the crank sensor is what controls the ignition spark.
hope that does it.
:)

Jan 20, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
2002 Chrysler PT Cruiser Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...