Question about Mazda Cars & Trucks

Open Question

2000 Mazda Protege. Ac light comes on at fan speed 1-3 but not 4. Fan only comes on at speed 4 but only barely. Replaced blower and fan switch. Any other helpful ideas?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Fan blower doesn't work

I have the same truck. Mine only worked on high. I replaced the blower motor resistor and it worked for a few seconds and then the resistor started to overheat and fry. I then removed the blower motor and found it to be pretty seized up so I replaced it along with another resistor and it works great. At any rate, be careful not to ruin a new resistor. If it shows any signs of getting hot when you first fire it up then turn off the blower motor immediately and replace it too. In my case, the worn out blower motor is probably what caused the original resistor and the replacement to fail in the first place.

Posted on Jun 30, 2009

Ad
  • 62 Answers

SOURCE: blower not working

Replace the dash controls. A common problem on beetles.

Posted on Jul 11, 2009

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

  • 1 Answer

SOURCE: 04 Wrangler AC fan only works on high speed (position4).

Its the switch behind the fan nob thats not making contact, you have to pop the cover off the dash where the radio fan and other gizmos are. Then remove the fan nobs by pulling them straight off after that unscrew the housing unit inside is the switch. You must carefully pry this open so as not to break the plastic clips holding it together the switch thats fryed should just pop out easy replacement fan switch! If my mind serves me right it costs 40$ to replace if you order from chrysler.

Posted on Aug 28, 2009

  • 12 Answers

SOURCE: 2000 jetta tdi: fan blower switch is not working

Have you by any chance replaced the blower motor relay?

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Blower motor not working on 4 1998 Mazda protege


check for power and ground at the blower motor. if this is good then hit motor. if it starts the motor needs replacing. then check the fuse then the fan speed switch for power and ground going to the switch and coming out of switch.

Jul 28, 2015 | 1998 Mazda Protege

1 Answer

The heat in my 96 mazda protege dosn't work


With the ignition and fan switches turned on check for power at fan motor.If you have power at the motor then wiggle and maybe pull on the blower motor resistor and if fan comes on just fix the connection.But when you check for power at the blower motor and don't have power then check the fan relay if it does'nt click when you turn it on then its faulty.

Oct 29, 2012 | 1996 Mazda Protege

2 Answers

I have a 2002 protege a/c wont work on all blower speeds and my friends 2000 blower will only work on 2 settings


Replace fan switch in dash.Or may even just need connections cleaned with some wd/40. To replace switch you need to remove dash and knob's, Then you have a switch that has the wires from fan to connector. . If these are ok and clean you need to replace your blower motor, Best of luck to you.
.

Apr 04, 2011 | 2003 Mazda Protege

1 Answer

A/C has quit working on fan speeds 2 thru 4.....it will only work on speed 1 but the fan itself still works on all speeds...it just seems to kick the a/c off on speeds 2 thru 4 and blow hot air ....2001...


You probably have a bad fan switch. I had the same issue and had it diagnosed and replaced. It fixed the problem, but it seems to be coming back less than 2 years later.

Jul 08, 2010 | 2001 Mazda Protege

1 Answer

2001 Mazda Protege' A/C button must have a short. When the fan knob is turned past 1, the A/C button turns off the A/C, no light, no cool air. The fan still blows, but the air only stays cool when the fan...


It's not the AC button but the fan switch. Had mine replaced with the same issue and it fixed the problem. It's beginning to fail again less than 2 years later though.

Apr 03, 2010 | 2001 Mazda Protege

1 Answer

2000 regal - cruise/fan blower control panel inop at same time


Sounds like it might be a bad ignition switch

Aug 22, 2009 | 2001 Buick Regal

2 Answers

2000 grand prix fan speed


i have been having that same exact problem with my 2002 grand prix for over a year now, and when my ac is on the lower setting the it doesnt work plus the headlights and lights on my dash go out. On Max everything works. i changed the blower resistor(about $35), still doesnt work. i changed all relays and fuses related to the ac, still doesnt work. i changed out the actual ac control switch in the dash, still doesnt work. i have changed everything but the blower motor and have asked every mechanic and auto parts retailer i come across and no one knows the answer. The best answer i got is that it is probably a wiring problem like a short somewhere.

May 28, 2009 | 2000 Pontiac Grand Prix

1 Answer

2001 Mazda Protege, Heater and A/C only works on 4 setting


I just had the same problem on my Nissan Xterra and the prblem is the resistor for the AC blower speed.Just get it and you will know.It is right behind and below the glove compartment and it looks like a card once you get it out. It is really easy to replace.

Mar 03, 2009 | 2001 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...