Question about Cars & Trucks

Open Question

Every time i turn off the ignition I loose tuning settings , have to manually re-set

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Every time i turn off the ignition I loose tuning settings on my radio , have to manually re-set


put yellow wire to permanent power (with ignition off).
Yellow is memory

Apr 16, 2017 | Cars & Trucks

1 Answer

How do I set the clock on my 2003 dodge dakota


  • Turn the Dakota's ignition on. Find the "Time" button on the top part of the radio control panel.
  • Push and hold the "Time" button. After a couple of seconds, you'll notice the hour display starts to blink.
  • Turn the "Tune/Scroll" knob to adjust the hour. When the hour is correct, push the "Tune/Scroll" knob. Now you'll notice the minute display blinks.
  • Turn the "Tune/Scroll" knob to adjust the clock's minute display. Push the "Tune/Scroll" knob to save the changes to the clock.

Jun 06, 2015 | 2003 Dodge Dakota

1 Answer

How to set clock in radio on a 2014 Jeep Patriot


Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds http://www.chryslercommercialvehicles.com/jeep/download/pdf/manuals/2014-Patriot-OM-1st.pdf page 240

Mar 12, 2015 | 2014 Jeep Patriot

1 Answer

Normal idle is fine...but sometimes i stop and motor shuts off


Dear Sir:
1( adjus the ignition timing according to the specification manufacturer
2) Readjust the GAP for spark plug.
3) See for any corroion, loose wires, burn, or broker, dust, dirty, solenoid defective,coil ignition defective. See the diagram attached, and proceed according.
God bless you.
5_25_2012_9_43_51_am.jpg5_25_2012_9_44_33_am.gif5_25_2012_9_48_59_am.gif5_25_2012_9_49_40_am.jpg

May 24, 2012 | Cars & Trucks

1 Answer

How do I set clock on a 2006 Pt Cruiser. I hold the time button down and can set hour but can't set minutes.


Clock Setting Procedure (digital clock page 242 of your owners manual)
1. Press and hold the time button until the hours blink.
2. Adjust the hours by turning the right side Tune/
Audio control.
3. After the hours are adjusted, press the right side
Tune/Audio control to set the minutes. The minutes will
begin to blink.
4. Adjust the minutes using the right side Tune/Audio
control.
5. To exit, press any button/knob or wait 5 seconds.

SETTING THE ANALOG CLOCK (page 238 of your owners manual)
To set the analog clock at the top center of the instrument
panel, press and hold the button until the setting is
correct. The clock will adjust slowly at first and then
quicker the longer the button is held.

Jan 26, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How do I set the clock in my 2006 Equinox... nothing in the manual


check page 3-39

Setting the Time
To set the hour, press the clock button. The clock
symbol will appear on the audio display and the hour
number will flash. Then turn the ADJ knob to increase or
to decrease the hour. To set the minutes, press the
clock button again. The minute numbers will flash.
Then turn the ADJ knob to increase or to decrease
the minutes. The time can be set with the ignition on
or off.
To synchronize the time with an FM station broadcasting
Radio Data System (RDS) information, press and
release the clock button to enter the clock set mode,
then press and hold the clock button for three seconds
until UPDATED appears on the display. If the time
is not available from the station, NO TIME UPDATE will
appear on the display.
RDS time is broadcast once a minute. After tuning to an
RDS broadcast station, it may take a few minutes for
the time to update.

Nov 30, 2010 | 2006 Chevrolet Equinox

1 Answer

Resetting oil life sensor


USING THE RADIO:

Follow this procedure to reset the GM Oil Life System.

Turn the ignition to ACC OR ON, with the radio off.
Press and hold the TUNE DISP button on the radio for at least five seconds until SETTINGS is displayed.
Press the SEEK PTYPE or the SEEK PSCAN up or down arrow to scroll through the main menu.
Scroll until OIL LIFE appears on the display.
Press the 1 PREV or 2 NEXT button to enter the submenu. RESET will be displayed.
Press the TUNE DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.
Once the message has been reset, scroll until EXIT appears on the display.
Press the TUNE DISP button to exit programming. A chime will be heard to verify the exit.

USING THE ACCELERATOR PEDAL:

Follow this procedure to reset the GM Oil Life System.

Turn the ignition to ON, with the engine off.
Fully press and release the accelerator pedal three times within five seconds.
If the CHANGE ENGINE OIL message flashes, the system is reset. However, if it stays on , it did not reset. Repeat the procedure.
Source(s):GM Service Manual

Jul 03, 2010 | 2006 Chevrolet Impala

1 Answer

Cant figure out how to set the minuetes on the clock


1. Turn the ignition key to the on position.
2. Press the time button until the hour starts to flash.
3. Turn the tune dial until the hour is set.
4. Press the tune button this will make the minutes flash
5. Turn the tune dial until the minutes are correct.

Feb 16, 2010 | 2004 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...