Question about Cars & Trucks

Open Question

I have a Cosco Quiet Time Elite swing. One of the leg braces is missing. Can this brace be ordered?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrhappyface
  • 205 Answers

SOURCE: inside door handle brace cracked, wont let me open door. how to fix and find part

these are known to break on these cars buy a new one and replace

Posted on May 30, 2009

Ad
  • 64 Answers

SOURCE: Broken top stress mount

All you need to replace that motor mount is a half decent socket set. The bottom mounts are holding up the engine and transmission. Good luck!

Posted on Jun 23, 2009

pippall
  • 1486 Answers

SOURCE: 1994 Toyota Corolla oil pan removal. Center brace

Remove engine mountings and lift engine.

Posted on Jul 06, 2009

  • 12 Answers

SOURCE: where is jack and wheel brace located

Yolu should find it under the front passenger seat. Tilt the seat back and it should be screwed in place with a single hand tight fastening

Posted on Feb 17, 2010

  • 3911 Answers

SOURCE: Where is the wheel brace and jack located on a

On my 2001 it was underneath the driver's seat.

Posted on Apr 20, 2010

Testimonial: "Excellent response thanks so much. This is the first time in 30 years of driving that I have known a jack to be stored under drivers seat."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the battery


Always remove the negative battery cable first. That will avoid the possibility of causing a spark trying to remove the positive first.
So you take a wrench and remove the negative post. If it is a sidepost battery, use an 8 mm wrench to remove the center bolt on the cable. If a top post battery, use the appropriate wrench to remove the negative cable terminal.
Now you can safely loosen and remove the positive battery connection.
Battery is now free to remove, but wait, there is a holding fixture on most batteries so it won't move around or tip over. Either a top bracket that hold battery stable, or there is a small little block at bottom of battery, like a wedge, to hold it secure. This block or wedge is retained by a small bolt, usually 1/2 inch size hex on the bolt (or 13 mm size, which is very close to 1/2 inch). remove this holding block or wedge and battery should come4 out. On some GM models there is a brace which is over the battery, and this brace must be removed for battery removal. Take one end of brace loose and swing it out of the way.

Apr 04, 2017 | Cars & Trucks

2 Answers

Is is safe to support engine by the oil pan while removing the subframe first, then the transmission?


no you need to support the engine assembly with a engine support brace.

Jul 05, 2015 | 2001 Ford Taurus

1 Answer

How to make clear braces look colored


If you want them colored ask your Orthodontist, he will tell you it is possible or not, because he knows the condition your teeth well. You can also find many good Orthodontist treatment as many choices are available in different bracket systems like metal braces, tooth-colored ceramic braces and clear brackets, etc.You can get better knowledge about Orthodontist treatment from the Orthodontics Munich, Eugnath.de.

Jul 16, 2013 | Cars & Trucks

1 Answer

How to install a alternator on a 94' cutlass


3.1L Engines - 1998-93 VEHICLES
(see Figures 5, 6, 7 and 8)
  1. Disconnect the negative battery cable.
  2. If necessary for access to the alternator, remove the air cleaner assembly.
  3. Remove the serpentine belt
  4. Label and detach the electrical connector(s) from the back of the alternator.
zjlimited_923.jpg

Fig. 5: After removing the serpentine belt, detach the electrical connector from the rear of the alternator

  1. Remove the rear and front attaching bolts, and unfasten the brace-to-alternator bolt.
zjlimited_924.jpg

Fig. 6: Unfasten the front and rear mounting bolts...

zjlimited_925.jpg

Fig. 7: ... then remove the brace-to-alternator bolt

  1. Carefully remove the alternator assembly, making sure all wires are disconnected.
If the alternator brace is removed, the studs must be retightened before installation or damage to the brace may result.


zjlimited_926.jpg

Fig. 8: Alternator (generator) removal and installation - 1992 3.1L engine shown (click image for zoom)

To install:

  1. Position the alternator into the mounting bracket.
  2. If necessary, attach the battery positive lead and nut to the alternator output terminal. Tighten to 71 inch lbs. (8 Nm).
  3. Install the brace-to-alternator bolt, but do not tighten at this time.
  4. Install the front and rear mounting bolts. Tighten the bolts as follows:
    1. Long bolt to 35 ft. lbs. (47 Nm)
    2. Short bolt to 18 ft. lbs. (25 Nm)
    3. Bracket bolt to 18 ft. lbs. (25 Nm)
  5. Check that tightening of the brace bolts did not bind the alternator.
  6. Attach the electrical connector(s).
  7. Install the serpentine belt
  8. If removed, install the air cleaner.
  9. Connect the negative battery cable.

Hope helps (remember to rate this answer).

Mar 23, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Where is the location of the air ride compressor on a 2000 lincoln continental?


When looking at the engine of your 2000 Lincoln Continental you will notice a coner brace on the left front corner. Directly under the brace you see the air ride comnpressor. you will have to remove the corner brace to gain access to the compressor. Once you do so it is just a matter of a few hard to get to nuts to remove. The compressor has rubber tubes coming from it that supply the air to the air bladders on your suspension. Don't forget the disconnect the battery prior to disconnecting the wiring clips in order to avoid causing electrical damage.

May 01, 2010 | 2000 Lincoln Continental

1 Answer

Where is the starter for a 1995 oldsmobile 98 regency elite


The starter motor for your Oldsmobile is mounted at the front lower part of the engine, just behind the radiator.
Book time to replace by an experience person is 1.1 hours.
If you are looking to do this yourself, disconnect the battery negative terminal and isolate it.
Remove any covers or braces in order to access and remove the starter.
Remove the wires to the solenoid on the starter, then the bolts retaining the starter to the engine.
There may be some shims between the starter and the engine. You may need to replace these with the new starter.
Hope your repair goes well.

KL

Dec 16, 2009 | 1994 Oldsmobile Ninety Eight Regency

1 Answer

Need diagram for clutch clutch fork zbar and linkage for 69 nova big block


Try obsolete chevy parts,on line.You can order parts,I believe they will have the diagram also.Brace on bell housing,bushing,axle,bushing,brace on frame.

Dec 12, 2009 | Chevrolet Nova Cars & Trucks

1 Answer

1996 Honda Odyssey. Loud vibration from heater fan behind dash. What is the best way to get to the fan / shroud ?


just above passengers feet area, pull the blower out, 3 or 4 bolts,most likely it has debris and leaves, making it out of balance. its also a good time to replace the cabin air filter. the cabin filter, you will need to remove the glove box, brace and cut a plastic brace out, the plastic brace was there for support when the dash was made, but now, it is no longer is needed

Oct 22, 2009 | Honda Odyssey Cars & Trucks

1 Answer

How do you get the lower pully bolt loose?


Do you mean the crank shaft pulley? put a socket and swing handle on it, brace it against the frame, and touch your key to turn the engine over a bit.

May 04, 2009 | 1999 Buick Regal

1 Answer

Looking for the electric brake plug-in on my 2004 f250 super duty. looked under the dash on the driver side and saw nothing like the plug. where is it located


Pull the panel under the steering column. Look on the right side of the brace on the right side. You have to reach through a hole to get to it. It is mounted at the top of the hole in the brace. It can be a pain to get to. It should be gray, rectangular with a small leg on one corner to assure it is installed correctly.

Jan 13, 2009 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...