Question about Smart Cars & Trucks

Open Question

Pentax water pump with smart head water goes into inlet but non comes out through the outlet

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: water is coming from outlet to heater core area. I

the 90 degree elbow is a drain hose, and it sounds like the heater core is clogged or has gone bad. Is the water draining on the inside of the truck too? check your floor board carpet under the dash.

Posted on Sep 15, 2009

  • 134 Answers

SOURCE: drilled hole in intake manifold at upper radiator outlet

Did the bolt break off flush with the top of the hole? or if you remove the cover is some bolt sticking up? if there is try and use vice grips to get ahold if the bolts if it is flush then drill the bolt out and re-tap the hole. Way cheaper and likely less work too...

Posted on Nov 02, 2009

  • 272 Answers

SOURCE: What is the valve that is in the hose coming from the water pump to the heater core 03 explorer and is this an inlet or outlet hose

Doesn't matter if IN/ OUT. Should be the vacuum operated heater ON valve.

Posted on Feb 17, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

87 dodge diplomat


You should be able to figure it out. It's only two hoses. Think inlet and outlet to the heater core under the dash. The inlet always comes from upper part of engine, where the coolant is the warmest and where it heats up first. The fitting will come from upper part of intake manifold or the cylinder head. then the hose goes to the firewall.
The outlet from the heater core carries coolant back to the engine and almost always to the water pump on the front of the engine. Makes sense, coolant goes back into the water pump and is circulated again back into the engine.

Jun 17, 2017 | Dodge Cars & Trucks

2 Answers

Whats the easiest way to figure out which hose is my input hose and which one is the output hose for the heater core in a 3.1L SFI OHV 6cyl.


Follow the hoses. The one that goes to the water pump is the outlet. The other one is the inlet.

Oct 31, 2016 | Cars & Trucks

2 Answers

Can you hook both heater hoses to the intake i put a 85 chevy 350 in it no were to hook on water pump


One exits the thermostat housing and the other needs to enter at a different point, usually the water pump.

Nov 04, 2015 | Cars & Trucks

1 Answer

Monte Carlo heater core


I don't know if top or bottom, but the heater core inlet will be the hose coming from either the intake manifold or a fitting on a cylinder head. The outlet from the heater core goes to the front of the engine, it goes into the water pump. I think all GM engines are like this, and almost all engine designs likewise. On a 1992 3.8L, for example, the heater core inlet hose comes from the intake manifold on the passenger side. The heater core outlet goes into a fitting on the water pump (lower front of engine).

Aug 02, 2015 | Cars & Trucks

1 Answer

1971 buick 455 fuel pump diagram


The pump has an inlet and an outlet. To find the inlet (coming from the tank), hold your finger over the openings and have someone crank the engine over. The fitting that has suction on it is the inlet-hose from tank goes there. The hose to the carburetor goes onto the pump's outlet fitting (with clamps).

Dec 12, 2013 | Buick Cars & Trucks

1 Answer

How do you install a thermostat on a 2001 suburban?


  1. Standing in front of the vehicle it's on the left front side of engine kind of low.
  2. Be sure to get a gasket as well.
  3. Drain the cooling system.
  4. Loosen the air cleaner outlet duct clamps at the following locations:
    • Throttle body
    • Mass airflow/intake air temperature (MAF/IAT) sensor
  5. Remove the radiator inlet hose clip from the outlet duct.
  6. Remove the air cleaner outlet duct.
  7. Reposition the outlet hose clamp at the water pump.
  8. Remove the outlet hose from the water pump.
  9. Remove the water pump inlet bolts.
  10. Remove the water pump inlet and thermostat from the water pump. Water pump inlet/thermostat assembly location
To install:

  1. Install the thermostat and water pump inlet to the water pump.
  2. Install the water pump inlet bolts.
  3. Tighten the water pump inlet bolts to 11 ft. lbs. (15 Nm).
  4. Install the outlet hose to the water pump.
  5. Position the outlet hose clamp at the water pump. NOTE
    Important: Align the arrow at the throttle body end of the duct with the throttle body attaching stud.
  6. Install the air cleaner outlet duct.
  7. Install the radiator inlet hose clip to the outlet duct.
  8. Tighten the air cleaner outlet duct clamps at the following locations:
    • Throttle body
    • Mass airflow/intake air temperature (MAF/IAT) sensor
  9. Tighten the air cleaner outlet duct clamp screws to 62 inch lbs. (7 Nm).
  10. Fill the cooling system and check for leaks.

Read more: http://wiki.answers.com/Q/Where_is_the_thermostat_located_on_a_2001_chevy_suburban#ixzz1TvIO3kpD

Aug 03, 2011 | 2001 Chevrolet Suburban

1 Answer

I need to replace a thermostat in a 2000 Chevy 2500 6.0 liter pickup


4.8L, 5.3L and 6.0L Engines To Remove:
CAUTION
The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
  1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

  2. Remove the bolts from water pump inlet.
  3. Remove the water pump inlet from the water pump.
To Install:
  1. Install the water pump inlet to the water pump.
  2. Install the water pump inlet bolts.
    • Torque to: 11 ft-lbs. (15 Nm)
  3. Install the radiator outlet hose.
6.6L Engine To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:
    • Water outlet 6.6L Thermostat housing removal gm_trk_sil25_02-04_66_therm_hous_rem.gif

    • Bolt for the fuel line bracket
    • Thermostat housing cover bolts
    • Thermostats and seals
To Install:
6.6L Thermostats and seals gm_trk_sil25_02-04_66_therm_seal.gif

  1. Install or connect the following:
    • Thermostats and seals to the thermostat housing NOTE: The rear thermostat (D) has 2 vent valves. Install with the vent valves towards the rear of engine.
    • Thermostat housing cover with a NEW gasket
    • Thermostat housing cover bolts and tighten the bolts
      1. Torque to: 15 ft. lbs. (21 Nm)
    • Fuel line bracket bolt and tighten the bolt
      1. Torque to: 15 ft. lbs. (21 Nm)
    • Water outlet
  2. Fill the engine with coolant.
  3. Test drive the vehicle to confirm the repairs.
8.1L Engine To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

    • Water outlet bolts (B)
    • Water outlet (A)
    • Thermostat (C)
To Install:
  1. Install or connect the following:
    • Thermostat
    • Water outlet
    • Water outlet bolts and tighten the bolts.
      1. Torque to: 22 ft-lbs (30 Nm)
    • Inlet hose to the water outlet
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Jan 12, 2011 | 2000 Chevrolet 2500

1 Answer

Where is the water pump gasket or the thermostat gasket in a 2002 cadillac escalade?


Thermostat Removal & Installation 4.8L, 5.3L and 6.0L Engines To Remove:
CAUTION
The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
  1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

  2. Remove the bolts from water pump inlet.
  3. Remove the water pump inlet from the water pump.
To Install:
  1. Install the water pump inlet to the water pump.
  2. Install the water pump inlet bolts. Torque to: 11 ft-lbs. (15 Nm)
  3. Install the radiator outlet hose.
8.1L Engines To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

    • Water outlet bolts (B)
    • Water outlet (A)
    • Thermostat (C)
To Install:
  1. Install or connect the following:
    • Thermostat
    • Water outlet
    • Water outlet bolts and tighten the bolts, Torque to: 22 ft-lbs (30 Nm)
    • Inlet hose to the water outlet
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Nov 09, 2010 | Cadillac Escalade Cars & Trucks

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smart Experts

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Are you a Smart Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...