Question about Cars & Trucks

1 Answer

Where are 2.4 99 Nissian Alitma heater hoses located

Ive been under car with it running water leaken from back of motor not fan side by rad

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,186 Answers

I don't know specifically but I have little doubt I could find them fairly easily if I needed to - they would be the only pair of coolant hoses connecting the engine to the heater matrix.

Knowing the approximate position of the heater matrix inside the car, the heater hoses would be aiming in that direction. It isn't unusual for the heater hoses to be hidden from view when looking from above and the best access is from underneath. These days an undertray is often fitted to reduce noise and drag and must be removed before any inspection or maintenance can be carried out.

Posted on Apr 15, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are heater Hose for 99 Nissian altima located


let the car run the hoses that get hot are the heater hoses or radiator hoses.

Apr 15, 2017 | Cars & Trucks

1 Answer

Fan relay location


what vehicle ?? usualy in fuse box under hood some are on or neer rads or do you mean heater fan the will be under passenger side dash in the heater box follow wires back from the heater motor they are attached to the relay some are real pain to get out

Aug 15, 2014 | Cars & Trucks

2 Answers

How do I change the engine radiator fan motors on my 2001 Buick Century?


  • Remove the passenger side kick panel using a Phillips head screwdriver. Pull the rug back from under the blower motor to allow enough room to drop the blower motor without the rug interfering.

  • 2

    Disconnect the electrical plug from the blower motor. Pull the rubber vent hose out of the blower motor.

  • 3

    Remove all the Phillips head screws securing the blower motor to the housing. Drop the blower motor straight down.

  • 4

    Install the new motor in reverse order of removal

Jan 13, 2012 | 2001 Buick Century

1 Answer

2000 chevy malibu keeps overheating. wont hold coolant. coolant boils out through overflow. and heater has stopped working


hi this could be caused by a couple of things, thermostat not opening is one of the main one, fan heater switch on the radiator is another, and obviously water leak is another, the first one thermostat, can replaced relatively cheaply, for a few bucks, you could do it yourself if you have the correct tools, to find out if it is thermostat, fill water first, run motor till it starts to get hot, feel the hoses on either side of the radiator ( top and bottom hoses be careful not to burn yourself in the process) if one is very hot, and the other is warm to cold, that will be the thermostat, second, the radiator fan switch, fill water, run motor, watch temp Gage, if by the time it has reached over half way on the temp Gage and the rad fan has still not cut in then this is normally a sign the switch on the radiator is u/s and needs replacing ( check fuse for fan to and relay this will also stop fan from working ) also to check for leaks, fill water, ( try not to spill any ) then if available a large cloth or sheet under car, run engine ( making sure first the other items have been checked ) and just observe for dripping water hope this helps

Feb 22, 2010 | 2002 Chevrolet Malibu

2 Answers

No heat on 2008 sienna, replace t-stat. one rad hose and one heater hose hot. other rad hose & heater hose cool


If your top rad. hose is cool and the engine is smoking hot, it probably is a blown head gasket. What does you temp gauge read ?

Feb 01, 2010 | 2008 Toyota Sienna

1 Answer

Overheating


then the water pump must be bad in it .Take the rad cap off and rev motor up if it goes down the the pump is working if it spays of look at the head gasket being damaged .Check and make sure spark plugs are not wet either if one is soaked signs of a leaky head gasket

Feb 21, 2009 | 2004 Nissan Sentra

1 Answer

Low heat running & no heat at idol


I'm betting your heater core is getting plugged up. With vehicle cooled off, drain rad, and remove heater hoses going into firewall at back of engine area. Cut & connect a garden hose of proper size to one of the copper tubes coming out of the firewall. Run water through it for a while to clear it out, now connect it to other tube & do the same. Re-attach hoses, fill rad with proper coolant mix and start engine with heater (not defrost) on while you do it. Keep topping up rad as coolant goes down. Let it run for a while, and rev the engine a little every once in a while and hold it there for 20-30 seconds just to speed up the air bleed and circulation process. Leave the cap off until it reaches normal operating temperature & wait for rad fan to come on, then off 2 to 3 times to make sure all air is out of the system. Put rad cap back on & top up coolant return bottle to proper level, and check that bottle for a couple of days just in case level goes down a bit after. If you have the time when heater hoses are off, I recommend plugging one of the tubes, (bottom one) and using the hose for flushing attached to other tube, and a funnel, and filling the core with "CLR" and letting it sit in there overnight to clean out calcium build up better inside the heater core. Then drain it, flush it & re-connect next day, but that's up to you. Good Luck, let us know how it goes.

Jan 10, 2009 | 2000 Dodge Caravan

1 Answer

HOW DO I CHANGE THE WATER PUMP ON A 99 JEEP GRAND CHEROKEE ?


At least you have the 4 liter 6. Once you get all the **** out of the way its like replacing a W/P on an "old school" engine, very much like a Ford or Chevy straight 6. 1) Remove radiator top retainer (the metal U that looks like its the top of the radiator (#13 or 14mm sockets I think). 2) To completely get if off you also have to remove the grill (4-6 phillips screws), then 3) unbolt it from the tubular bumper retainers underneath the grill. 4) DO NOT remove the latch cable - no need. 5) Remove the top bolts holding down the fan shroud. Lift the shroud off its bottom "tabs" and push over the fan. 6) Using #10mm socket remove fan from fan clutch, then remove bolts holding fan clutch onto water pump pulley. 7) Pull out shroud, then fan, then fan clutch. Be very patient, lots of wiggling may be needed. 8) Locate belt tensioner on idler puller below the Power steering pump. Losen very little the pulleys center bolt (10mm), then use a 10mm w/entension to losen the pulley's tension (use counter clockwise/normal rotation to losen). 9) Draw a diagram of the belt routing - you will Never remember it correctly otherwise. 10) Tap the w/p pully and pull if off - do not hit radiator fins! 11) Drain the radiator (clockwise/right rotation opens petoc from factory radiators - counterclock used on aftermaket rads). 12) Remove lower raditor hose at radiator, then at pump (it will be a challenge). 13) Remove upper radiator hose from rad and from thermostat housing. 14) losen the Rubber heater hose from the metal hose screwed into the W/P. 15) Remove 4 bolts from W/P (13 or 14mm I think). The one at the 4oclock position is longer than the others. One is hidden at 6oclock.
16) Remove 2 bolts (14-15mm??) on bottom of Power Steering mount - these go through the W/P case to the block. You may also need to losen the top PS bolts so the PS Bracket can be loose at the W/P case. 17) Wiggle the W/P out from under the PS bracket. and pull off. (16b if needed, remove the upper idler pulley near the A/C unit.) 18) Remove the Thermostat (upper hose return) housing. Scrape off old gasket. Replace with 160deg or 190deg thermostat. Use silicone on gasket. 19) Carefully use a 17 or 19mm box wrench to remove the metal heater hose return line from the upper part of the old water pump. Coat threads with spark plug thread antiseize and screw onto new W/P. 20) Install new W/P gasket w/silcone, be careful to Not block the water holes. 21) Slide W/P under the P/S bracket and jiggle into place. Hand thread one of the top bolts to hold the W/P in place. 22) Insert the P/S bracket bolts and lightly tighten. 23) Jiggle W/P around and insert other bolts, start with the 6oc hidden bolt. Add remaining bolts and tighten to 25 or 250?ftlb (about 3/4 past socket-snug). 24) Tighten ALL P/S bolts. 25) Adjust metal heater pipe. Reinstall rubber heater hose. 26) Reinstall W/P pulley and Fan clutch, and upper idler if it was removed. 27) Thread NEW Belt on pulleys. 28) Tighten tension on idler. Tighten idler axle bolt. 29) Install lower rad hose. 30) Slide shroud over pulleys. 31) Install fan on clutch. 32) Clip shroud retainer bolt mounts back on top of radiator. 33) Install shroud. 34) Connect upper hose. 35) Reinstall radiator retainer. 36) Bolt retainer to Tubular bumper mounts. 37) Reinstall grill. 38) Wonder where the extra bolts etc are supposed to go. 39) Cuss - pray -cuss - pray. 40 ) sip some beer. 41) carefully inspect everything to ensure its back to the way it looked before (several pictures from a digital camera taken during the disassembly will help). 42) Close the rad petok. 43) Add 1 gallons of antifreeze. 44) Start engine and add another gallon of A/F. 45) Turn heater controls to HOT inside (no need for fan). 46) Water guage should show 180 to 210F. 47) Add 1 gallon of water. 48) Install New 18PSI rad cap. 49) Turn off engine and add water or A/F to overflow tank. 50) 1 hour later open Cap to see if level has settled. Add Water as needed to fill rad.

Dec 24, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...