Question about Cars & Trucks

1 Answer

Where are heater Hose for 99 Nissian altima located

There is a hose on back of head it looks like 1 inch hose

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 378 Answers

Let the car run the hoses that get hot are the heater hoses or radiator hoses.

Posted on Apr 15, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are 2.4 99 Nissian Alitma heater hoses located


I don't know specifically but I have little doubt I could find them fairly easily if I needed to - they would be the only pair of coolant hoses connecting the engine to the heater matrix.

Knowing the approximate position of the heater matrix inside the car, the heater hoses would be aiming in that direction. It isn't unusual for the heater hoses to be hidden from view when looking from above and the best access is from underneath. These days an undertray is often fitted to reduce noise and drag and must be removed before any inspection or maintenance can be carried out.

Apr 15, 2017 | Cars & Trucks

1 Answer

...i am looking for a diagram for a 1999 3.0L ford windstar engine to locate the heater hoses


There is a small radiator which forms the heat two hose will be running to that inside of car trace them back to engine normaly one from top of engine neqr thermostat half inch hose

Nov 13, 2015 | 1999 Ford Windstar

1 Answer

Just had radiator replaced, leak has developed around housing/gasket of hose running to passenger side just to side of engine and slightly behind. My mechanic doesn't know what the part is we are looking...


is it actually on the engine? I ask because you say it is to the passenger side and just behind the engine, that makes me think it is a heater hose, the heater hoses go from the water pump to the heater core which is located on the passenger side, the difference between heater hoses and radiator hoses is the size and of course location, heater hoses are generally about 1/2 inch to 1 inch, with radiator hoses being between 1 3/4 and 3 inches

Feb 09, 2010 | 1997 Acura CL

1 Answer

The heater will not heat i think it the thermostat how do i put it in can you show mw a diagrham this is a 2002 nissian altima


Which engine ? Put a drain pan under top radiator hose. There should be a cast part attached. Remove, you will see thermostat, pull install new, clean old gasket off, install new gasket with ORANGE HIGH TEMP PERMATEX SILICONE, re-assemble

Feb 02, 2010 | 2002 Nissan Altima

1 Answer

Cylinder head removal on 2005 nissan altima 2.5 engine would like to know how to remove the camshaft to remove the head bolts


CYLINDER HEAD REMOVAL

2.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Nov 13, 2009 | 2005 Nissan Altima

1 Answer

Overheating


then the water pump must be bad in it .Take the rad cap off and rev motor up if it goes down the the pump is working if it spays of look at the head gasket being damaged .Check and make sure spark plugs are not wet either if one is soaked signs of a leaky head gasket

Feb 21, 2009 | 2004 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...