Question about Honda Civic
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You probably hit one of the veins on the squirrel cage, mounted on the fan motor. You might be able to take the fan out and straighten these, to get the vibration out, if not you'll have to replace the whole fan. Good luck. I hope you can straighten it and don't have to replace.
Posted on May 29, 2009
Alright, let's just jump right into it. Get down and low and at the front of your center console you'll find two clips holding it in. There's one on the driver's side and one on the passenger side.
Okay so now how the *#$@ do I remove those clips? If you pull they don't come out...and if you pry you'll just scratch your console. Here's how: Look carefully and you'll see the center is a little circle. Gentley push it in...voila..off it pops. Repeat this for the other side. 2.
Alright now it's time to head to the back. You should recline your seats all the way forward and slide them up front. This will give you plenty of room to work. Get down low and you'll see a screw holding the back in -- once again you'll find it on both sides.
Simply take your Phillips head screwdriver to the ****** and unscrew it on both sides. 3.
Look carefully and you're going to see that the top of your center console is comprised of two pieces. One that stretches from the front of the console to just behind the shift boot. The second piece stretches from there to the back of the console.
The second piece is what we're going to remove. Here's how to do it. It's only held down by a few clips so all you need to do is pry it up. So whip out your flat head screw driver, or other prying device along with a cloth to prevent your crazy @$$ from prying up the plastic too. Start and the back and pry it up. 4.
You can theoretically now just pull the whole thing straight up. However what I found to be easier was to pry up one side and get your fingers underneath then pull from left to right (or vice versa) to pop off the front clips. The front clips tend to be in stiffer than the ones around the side and rear.
*POP* The entire center piece should now be free! 5.
Now you're able to lift the piece straight up.
Simply slide the piece up and forward taking care not to scratch anything 6.
Alright you'll probably discover you can't quite get it past the brake lever.
Yup...excellent deduction Sherlock..the gear shifter seems to be in the way. 7.
Alright time to move out of the way Mister Gear Shifter
Slide that baby into 1st gear (Make sure you didn't lower your hand brake!!!) 8.
It's free! Now you have room to work!
Okay now that the gear shift is in first...you have room to carefully slide the piece forward and out without scratching anything. So now that you have the rear piece off, you want to remove the front piece right?
Well as you can see here, all that's holding it in place are these two screws on this panel. Take your mighty Phillips head screwdriver and go buck-wild on those two screws
You've now successfully removed everything that's been holding the center console down.You should now be able to slide the center console back and forth. There you should be able to remove it now..and you should see this
Posted on Oct 13, 2009
Sorry to hear all this has been going on and the obvious hasn't been detected by a shop. All those parts probably would not of had to be replaced. This is a classic systom of a blown head gasket. Not every head gasket blown will have coolant in the oil. Compression leak from a cylinder will enter water passage in head and blow out the coolant because compression is greater pressure than coolant system pressure.
Posted on Dec 12, 2009
will it start with a boost? either the starter motor or the battery. take the battery to auto zone and they will test it for you.
Posted on May 26, 2010
Placed jumper cables on the car to try & jump alarm sounded pressed the unlock button & was then able to start car without any problems.
Posted on Nov 06, 2011
Tips for a great answer:
Mar 10, 2016 | Honda Cars & Trucks
Sep 14, 2017 | 1999 Honda Civic
Nov 20, 2017 | 2008 Honda Element
Oct 12, 2011 | 2005 Honda Civic
May 24, 2010 | 1998 Honda CR-V
Feb 26, 2010 | 2002 Honda Civic
Jan 15, 2009 | 2005 Honda Civic
Apr 21, 2018 | Honda Cars & Trucks
33 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: