Question about Cars & Trucks

Open Question

Sunpro super tach 2, had worked perfectly, less than 1yr old. Since having the engine out and back in it won't go above no.1 on guage. connections seem fine, set on the correct cylinder. Please help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: How do I hook-up Sunpro Super tach 2.

I've got an install diagram for that around here somewhere but for now, the trigger wire to run the tach itself goes to the "tach" connection next to the "Bat" terminal on the distributor cap. one wire attaches to your dash lighting so it comes on with the dash lights and dims properly, the other wire is likely a ground. If I don't add to this later, try googling Sun electronics...I am fairly sure they have an install page.

Posted on Jan 04, 2010

Ad
MECP Guy
  • 344 Answers

SOURCE: 2004 toyota corolla tach wire

you can also solder the wire to the tach wire, this way it won't come off and cause a malfunction

Posted on Jan 17, 2010

  • 1 Answer

SOURCE: Check engine light flashing runs

This could be a bad cam sensor that hasnt gone yet. It would explain why you are running to lean.

Posted on May 12, 2010

  • 834 Answers

SOURCE: How do I install a

The Black wire will connect to body ground, and it should be a good solid ground and if this wire is not grounded well then you might receive a primary voltage shock if you touch anything that is metal or grounded inside of the vehicle when the engine is running.

The Red wire should be connected to power when the key is in the "Run" position only, and a good place to find that source is one of the "IGN" connections at the fuse panel using a covered female spade connector. Use a test light and be certain that the connection only has power when the key is in the "Run" position, and has no power when the key is in the "Off" or "Accessory" position.

The White or Yellow wire should connect to the "LPS" connection at the fuse panel next to the LPS fuse using a covered female spade connector.

The Green wire will connect to the "-" negative side of the ignition coil or to the "Tach" or "Test" lead that runs from the negative side of the ignition coil. To locate the lead run down the wire from the negative side of the ignition coil and the lead should break off from that wire and it should have a tag on the wire that will say either "Tach" or "Test" (sometimes it is just an empty black wire connector) and that is if the lead does not come straight off from the wire connector at the ignition coil. If there is no lead you can get a wire tap connector to tap into the wire from the negative side of the ignition coil and then use a covered male spade connector to connect the Green wire from the tachometer to the wire tap connector.

Here is a diagram to help assist you and if you can not download the image right click on the image and then select "save picture as..." or "save image as..." and from your image viewer you should be able to read this diagram or print it out, and let me know if you require any further assistance.


d756391.gif

Posted on Aug 20, 2010

  • 1565 Answers

SOURCE: Dodge 2002 Grand Caravan started missing at all

http://www.youtube.com/watch?v=HPvX190txvk

Posted on Nov 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just bought a sunpro super tach2 and it shows that it is running to fast. whats the problem


There should be 2 adjustments on the back. A switch for 4-6-8 cyl use and a slider to fine tune the rpm. If you know your car idles at 750rpm, move the slider until the tach reads 750. The switch for cylinder numbers should be self-explanatory and must be set first.

Feb 12, 2015 | Cars & Trucks

1 Answer

1984 nissan pickup dead speedo, tach and fuel guage


Have you checked to see if the instrument panel has a good ground connection? Rust is NOT your friend when it comes to electrical connections!

Apr 22, 2017 | Cars & Trucks

1 Answer

The guages on my F350 super duty go crazy while driving


Two possible fixes : 1. Replacing the GEM module. 2. Check the electrical connections including wires.

Jun 01, 2010 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

I have a sunpro after market tach. i need the color coded diagram to install it,can anyone help me?thanx


Tried going to sunpro online? paste this in and it should get you there:http://www.google.com/search?q=sunpro+tachometer+wiring&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US Ive always found that going to the source is better than getting it second-hand.

Apr 23, 2010 | Chevrolet Silverado Cars & Trucks

1 Answer

I1999 dodge ram 1500 5.2 and need to no how to put a tach in


Red wire would go to ignition battery, the black to ground. The third wire, probably green or blue, goes to the negative side of the ignition coil. Is there a wire for dash illumination?

Mar 10, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

How do I hook-up Sunpro Super tach 2. Wires: 1 each - green, red, white, and black? Or in general how do these type tachometers hook-up?


I've got an install diagram for that around here somewhere but for now, the trigger wire to run the tach itself goes to the "tach" connection next to the "Bat" terminal on the distributor cap. one wire attaches to your dash lighting so it comes on with the dash lights and dims properly, the other wire is likely a ground. If I don't add to this later, try googling Sun electronics...I am fairly sure they have an install page.

Jan 04, 2010 | 1985 Chevrolet K1500

1 Answer

I have a 1994 GMC Sonoma SL and it doesn't have a tach in it, so I brought one made by Sunpro. And my problem is I've never hooked one up. So is there anybody out there that can tell me how to do it? and...


Do you have the instructions that came with it? If not, you can get them online at the sunpro website:
http://www.sunpro.com/user_manuals.php
If you need more help, let me know

Aug 09, 2009 | GMC Sonoma Cars & Trucks

1 Answer

2004 toyota corolla tach wire


you can also solder the wire to the tach wire, this way it won't come off and cause a malfunction

Jul 03, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...