Question about Cars & Trucks

Open Question



Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Oil pressure low is on,and it say stop engine can I drive it if I put oil in it

If the oil PRESSURE is low, AND you have plenty of oil in the engine, DO NOT drive it.

If the oil level is low, add oil to the "full" mark on the dipstick. Start the engine, and see if the light goes off. If the light goes off, you can drive it.

Nov 06, 2015 | Cars & Trucks

1 Answer

What's the proper oil level for a Chevy silverado crew cab 4 wheel drive.

The dip stick should be marked to show you what the level should be. Pull it out, wipe it off with a rag and put it back in and pull it out and take a look at the oil level.

Apr 18, 2014 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

How to check transmision oil on 2006 charger

use owners manuel to locate dipstick(oil is red)take car for a drive until engine is at normal running temperature,park on level surface leave motor running,remove dipstick wipe it off put back in,take it out and check oil level.

Nov 24, 2012 | Cars & Trucks

1 Answer

Ho0w do i test the blower motor on my 2006 kia optima

put power and ground direct to it with the cars harness disconnected

Sep 17, 2012 | 2006 Kia Optima

1 Answer

Automatic transition no gears

Check the automatic transmission cable adjustment and fluid (ATF) level. Be sure that the car is in P, hand brake pulled, the engine is running and is at operating temperature. Do the following:
1. Take the transmission oil dip stick out, wipe it with fiber free tissue paper or clean piece of cloth and insert the dip stick back to its place.
2. While the engine is running, take the stick out again place it horizontal and see the oil level.
3.If the level is at upper mark or in between upper and lower marks it is OK. Put the stick back to its place.
4. If the transmission oil is less than lower mark, add the manufacturer specified oil up to the mark, and test drive the car.
5. If the oil level is found to be OK, remove the transmission filter, clean it or replace it, and test drive the car. It should now work.

May 27, 2012 | 1985 Toyota Corolla

1 Answer

Car does not shift when cold and bangs from park to drive runs fine when warmed up had a trans flush last week still having problems 2000 elantra 4 cyl

check the oil level by applying handbrake then start engine and put in reverse ,then check oil level if oil level ok have a drive around dealers and trade it in quick before you have to pay out for a new gearbox

Feb 17, 2011 | 2000 Hyundai Elantra

1 Answer

Wont move in drive.but if you put it in nuetral and rev the motor to1200 rpm and dop it in drive it works fine until you stop again

oil level low ,start engine ,handbrake on then select reverse and then check oil level ,think you are about at a least a litre short

Dec 23, 2010 | Subaru Legacy Cars & Trucks

1 Answer

4 whell drive roar starting at 25mph

that really sounds like you need to verify the level of the trans-axle oil and/or the transmission oil. if you are unsure, or if you didnt perform the change of the oil at the required intervals, you should stop in a pep boys, jeffy lube or similar store and have the fluid levels check.

the transmission oil is easy to check with a dip stick in the engine (not the same to the engine oil), and the trans-axle oil, you will have to remove a bolt in the axle and check with your finger if it is in level.

Apr 27, 2010 | 2003 Chevrolet Trailblazer Ext

1 Answer

Transmission stuck in neutral (automatic) won't engage drive or reverse

first i would check the transmission oil, do this by starting the engine and leave it running, select all the gears (park, Reverse, neutral etc) then put it back to neutral, leave engine running then locate the transmission dipstick in the engine bay, remove and wipe the dipstick, replace then pull out again, if the oil is showing between the cold and hot marks then level is ok. I shoing lower or none, top up the oil level with automatic tansmission oil, keep rechecking the oil level as adding oil as to ensure it is not over full. will need to select all gears again before checking oil level again.
If the oil level is correct than quite likley a Transmission failure will require mechanic.

May 02, 2009 | 1988 Nissan Pulsar

1 Answer

Auto trans wont engage into drive unless you rev motor

check oil level with engine running,handbrake on, chock drive wheels,and put in reverse check oil level

Dec 01, 2008 | 1989 Nissan Sentra 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13632 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides