Question about Cars & Trucks

1 Answer

Brakeschange front pads - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,696 Answers

Hello John doer,

Always a good idea... EASY too!

Manuals are inexpensive... but necessary.

Just before you run out of pads.
(don't forget to flush out that old brake fliud)
((and if the rotor surface is less than perfect... FIX IT)).

Saves big money!
Carnac the Magnificent

Posted on Apr 15, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change brake pads


For starters the front and rear us disk pads and it is not hard to do. On the front jack up the front and us jack stand for safety. After you take of the wheel remove the two bolts at the back of the brake caliper remove the caliper and then the old pads us a C- clamp with one of the old pads installed in the caliper then just us the c-clamp to push the cylinder all the way in until it will go no further install new pads put back on. But before you do the next side hit the brake to push the cylinder back out. Go to other side do the same thing. On a side not you only need to replace the rear brakes every other time you do the front. The front wear twice as fast as they do most of the stopping.

May 19, 2013 | 2004 Buick Century

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

2 Answers

My brakes sound like they are grinding


check rear rotors and front rotors for rust buildup (flahlight helps). does the vehicle shake when you come to a hard stop? You will either need to have a front or rear or both brake job (rotors cut or replaced and new brake pads) If the vehicle is shaking when coming to a stop, its probably your front pads. If your hearing the noise from the rear its the rear pads or it you hear it from the front its the front pads. If there significant rust build up or your pads are low a brake job is recommended.

May 04, 2011 | 2008 Nissan Armada

2 Answers

Are the front and rear brake pads the same or different sizes on my 2003 Silverado 1500 (4wd)?


YOU HAVE TO BUY FRONT PADS FOR FRONT BRAKES AND REAR PADS FOR REAR BRAKES THERE IS SOME DIFFERENCE.

Mar 04, 2011 | 2003 Chevrolet Silverado 1500

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

2 Answers

Change hyundai accent 2001 front brake pads


may have siezed caliper slide pins suggest buy reman loaded caliper assembly

Oct 05, 2009 | 2001 Hyundai Accent

1 Answer

I'm trying to replace my front pads there are 2


Replace left and right brake pads at the same time. Do not replace brake pads for one side of the vehicle only.
  1. Raise and support front of vehicle.
  2. Remove tire and wheel assemblies.
  3. Remove pad pins and springs.
  4. Remove brake pads, then shims.
  5. Reverse procedure to install. When installing new brake pads, push caliper piston inward using piston compressor No. 490221600C or equivalent.

nothing Special that I see

Jul 14, 2009 | Mazda 323 Cars & Trucks

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...