Question about Ford Cars & Trucks

2 Answers

Had to replace fuel pump relay on 2003 Ford Ranger. Now it won't turn over.Checked all fuses and battery. Could it be anti theft system? Where's valet switch?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,089 Answers

Is the little red light on the top of the dash panel flashing fast when trying to start the vehicle ?

Posted on Apr 15, 2017

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

Do you mean it wont cranck if so check if you have power on your starter if not change ignition key but before check battery and circuit good luck

Posted on Apr 15, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford mustang 3.8 no power at fuel pump fuse is good relay is good it does have a anti theft device, inertia is good


You have a fuel pu,p driver module that gets the power from the inertia switch and the power for the fuel pump comes from that module. I would start by checking for a wiring problem. Below is a picture of where that module is located. At the plug of the module you want to make sure you have good continuity from the pink and black wire at the module to the inertia switch. Then you will want to make sure you have continuity from the fuel pump to the module in the brown and pink wire. That should be the power source to the fuel pump. One other thing to keep in mind and that is the PCM controls ground to the fuel pump so this may be an issue. Try that first to see if you have a wiring problem. If you have power from the inertia to the module but no power coming out of it to the fuel pump this may be your problem. Hope I was able to help...

2_29_2012_9_12_02_pm.jpg

Feb 29, 2012 | 2000 Ford Mustang

3 Answers

01 ford explorer sport won't stay running. turns over fine and starts but quits right away


Check for vacuum leak at intake manifold or bad fuel pump relay or have fuel pressure checked to see if fuel pump is working properly 40-45 psi it should be pumping

Dec 18, 2011 | 2001 Ford Explorer Sport

1 Answer

Im lookin for the fuel pump fuse in my 2003 ford ranger


Hello,

In your power distribution box in your engine compartment (Ford recommends

disconnecting your battery before servicing fuses / relays in PD BOX )

fuse # 9 - 20 amp mini-fuse for fuel pump relay and RAP module

relay # 5 - is the fuel pump relay in your PD BOX

also , the fuel pump inertia (shut off) switch is in the right front passengers

footwell by the right front kick panel.

Thanks..

Jun 16, 2011 | 2003 Ford Ranger Regular Cab

1 Answer

I was deppressurizing the fuel system in a galant 2003 2.4L 4 cylinder engine. pulled the fuel pump relay then put it back in correctly Car wont start. both relays r good fuel pump does Not turn on at all...


disconnect the battery, this should reset the computer.Make sure that you have the radio code for the anti-theft and know how to reprogram it(enter the code0 Good Luck Tim

Apr 18, 2011 | 2003 Mitsubishi Galant

1 Answer

2000 Jeep Grand cherokee Laredo wont start. Engine turn over . No noise from fuel pump with ignition on. Replaced fuel pump and filter.Turn ignition on- pump did not run.Jumped the fuel pump at the pump...


sounds alot the the pcm it controls the fuel pump and ign system but the anti theft would keep it from starting because the key has a transponder in it programmed for that vehicle and that would kill all ign if triggered

Sep 22, 2009 | 2000 Jeep Grand Cherokee

2 Answers

I cant get my truck to start because of the anti-theft lock.


Do you have any engine codes?
Does your fuel pump turn on and do you get sufficient fuel pressure?
Do you get spark? Power to plugs, ignition module, coil packs?

Check all fuses and relays?

May 10, 2009 | 1994 Ford F150 Styleside Supercab

1 Answer

Truck Won't Start At All


before replacing the starter get a volt meter and test the voltage coming out of the voltage regulator which the power comes from the battery to the regulator down to the starter also make sure all wires on the starter are clean and what I mean is from rust because I had an f150 that did the same thing

Nov 18, 2008 | 2003 Ford Ranger Regular Cab

1 Answer

Anti-theft


the valet switch you have to find this in your truck press and hold should disengage the anti theft module

Jun 02, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...