Question about Cars & Trucks

1 Answer

Crankshaft seal keeps leaking how do I align da seal, any pics

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 25 Answers

There are thin sleeves to put on the crankshaft to enlarge the shaft to cover the worn out area on the crankshaft ,so the seal will keep the oil in , These are available at a good auto parts store I believe we called them speedy sleeves. Older fords had problems with axels leaking differential oil on to brake shoes. Very common problem with small block chev V8's to leak oil at front cover of the motor. Just slide the sleeve on, and install the seal

Posted on Apr 15, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: 2005 dodge stratus keep blowing out crankshaft

check for pcv blockage

Posted on Nov 03, 2009

  • 1 Answer

SOURCE: crankshaft seal blows out oil leak

The fix is replacement of motor!! I have the same problem and have already paid $700 in repairs to fix seal just to find out that the seal is being knocked out by loose crank shaft..Car had 60000 miles when I bought it 4 months ago, from a dealership, and now it needs a motor replacement..I stiil owe $5000 on a car that is worth $0..Dodge did not give the 100000 mile warranty they love to advertise on TV for the '06 Stratus..They only gave 36000 warranty because they did not think it would last much longer..Will never buy Chrysler product again!! They do not stand behind what they sell or they would have 100000 mile warranty on all their cars..

Posted on Feb 11, 2010

  • 14585 Answers

SOURCE: I have replaced the front

First check the compression on the cylinders. If they are low then the rings are bad. This will cause major oil leaks all over the engine. The only other thing would be that the main bearings are bad. to much slop and blowing the seal.

Posted on Aug 07, 2011

alicantecoli
  • 22095 Answers

SOURCE: Can sum1 plz tell me wat cn i do? I replaced all 3

could be a problem with the oil pressure relief valve ,no idea where it is though

Posted on Feb 16, 2012

  • 6468 Answers

SOURCE: how to change the outer seal near da tire on a 1985 chevy silveraldo rearend

you need to remove the cover in the middle of the rear axle rotate the drive shaft until you see a bolt with a 5/16 head on it slide out the pin that the bolt held in remove the c clip that holds the axle in slide out the axle and replace the seal you should do both sides while its apart then put it back together and fill threw the plug on the front side that uses a 3/8 drive

Posted on Mar 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front seal replacement


Hi No Name, The most likely place of the leakage on your car is the front crankshaft oil seal. The oil pan (sump) is fitted with silicon from a tube as the gasket. It rarely leaks unless someone has broken the seal, which is difficult and usually needs a special tool for removal. To replace it you'll need to disconnect the battery, remove the PK (Serpentine) belt and the power steering pump belt and the front engine mounting (Front of the engine but fitted onto the side of the body) Next remove the crank shaft pulley, (a difficult part of the job, made easier if the starter motor is removed and a dog tooth tool is bolted into the most suitable starter motor attachment bolt holes, the dog tooth is used to lock the flywheel while removing the crankshaft bolt holding the pulley (which is torqued to 76 nm when re-fitting. Use a puller to remove the pulley from the crankshaft and then remove the ten mm bolts holding the two parts of the timing belt cover. Set the engine to T.D.C (Top Dead Center) and look for the match marks for re-timing the engine when refitting the timing belt. Once alignment has been achieved release the bolt holding the tensioner bearing and push it all the way open, releasing all tension from the timing belt and remove the timing belt. The oil seal can now be removed from its housing. Fit a replacement oil seal smearing a light coating of grease on the seal lip. Press evenly into place, making sure of an even flush fit. Replace the timing belt with a new belt, Re-align the belt so that the match marks align precisely to those on the gears by fitting and adjusting on the straight side of the belt. Once correctly fitted, gently release the tensioner bearing until it comes into full contact with the belt and hand tighten the fixing bolt and then loosen half one turn. Remove the dog tooth tool. Screw in the crankshaft pulley bolt and apply enough force to take up slack and tighten the tensioner. Remove the crankshaft bolt and then reassemble opposite to disassembly. Remember to refit the dog tooth for re-tightening the crankshaft bolt.

Jun 28, 2014 | 1993 Toyota Corolla

2 Answers

1998 camry oil smells like fuel, 260,000 miles. out runs strong, Just replaced the valve gaskets, can anyone help me figure out what's wrong?


These engines do have chronic oil leaks onto the exhaust, hence the burning smell. When cam cover gaskets are replaced it is best to use the genuine Toyota parts, they seem to have some quality which lasts better.

Other places which leak are the distributor shaft o-ring seal, and crankshaft nose seal, behind the timing belt sprocket. These can be replaced. The crankshaft rear main seal will leak, but is expensive, so just leave it.

Oct 21, 2012 | 1998 Toyota Camry

2 Answers

MY 2000 RODEO IS LEAKING OIL ON DA GROUND WHATS THE PROBLEM


oil leaks can come from many things.like front timing cover crankshaft seal, rear main oil seal,with engine running look under car around oil pan area check see if you see heavy oil leak which will come from loose or damage oil filter and seal or check oil pressure sending unit at bottom right rear engine block or right rear corner of the oil pump.if oil leak small leak the front crankshaft seal and rear main seal leaking .

Nov 14, 2011 | 2000 Isuzu Rodeo

1 Answer

How do you aline the timing marks on the cam and crank on a 97 toyota camry with a 2.2


Hi, the procedure is pasted below. There is a good rundown with pics at the following post:
http://www.toyotanation.com/forum/showthread.php?t=264429
Please let me know if you have questions.


REMOVAL & INSTALLATION
5S-FE Engines
  1. Remove the timing belt covers as previously detailed.
  2. Raise the engine just enough to remove the weight from the engine mount on the right side.
  3. Remove the thru-bolt, two nuts, and right hand mounting insulator.
  4. Remove the retaining bolts and remove the right hand mounting bracket (from the side the alternator was removed from).
  5. Remove the timing belt and timing belt guide. If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear.
  6. Remove the bolt retaining the No. 1 idler pulley and tension spring.
  7. Remove the No. 2 idler pulley.
  8. Remove the crankshaft timing gear , if it can not be removed by hand, use two flat bladed tools to pry it off. Make sure to position shop rags to prevent damages to the components.
  9. Remove the nut retaining the oil pump pulley.

To install:
  1. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
  2. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
  3. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly.


NOTE Remove any oil or water on the idler pulley and keep it clean.
  1. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
  2. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys.


NOTE If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.
  1. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
  2. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  3. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
  4. Align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.
  5. Tighten the set bolt to 27 ft. lbs. (37 Nm).
  6. Turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  7. Install the timing belt and check the valve timing as follows:
    1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
    2. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.

  8. Install the upper (No. 2) timing cover with a new gasket(s).
  9. Align the two clamps for the engine wiring harness with the cover mounting bolts.
  10. Install the spark plugs.
  11. Install the right mounting insulator with bracket. Tighten the bracket bolts to 38 ft. lbs. (52 Nm), insulator nuts to 38 ft. lbs. (52 Nm) and thru-bolt to 52 ft. lbs. (71 Nm).
  12. Install the No. 2 engine mount bracket and tighten to 38 ft. lbs. (52 Nm); install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm).
  13. Lower the engine.
  14. Install the alternator and alternator bracket.
  15. Install the drive belt and adjust the tension.
  16. Install the cruise control actuator with bracket.
  17. Install the fender apron seal and right engine under cover.
  18. Install the right front wheel.

Jul 24, 2011 | 1997 Toyota Celica

3 Answers

2002 Pontiac Sunfire GT. 2.2 Litre Ecotec Engine. Concern: Front Seal is leaking. Question: Does the engine need to be pulled to replace the seal?


No. The crankshaft pully can be removed through the right wheel well area. (This is the hard part) Once the pully is off, the seal is relatively easy to change.

Jan 25, 2011 | 2003 Chevrolet Cavalier

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

How do you time a 350 gmc motor


4.8L, 5.3L and 6.0L Engines
    • Timing mark alignment-4.8L, 5.3L & 6.0L 9308kg61.gif

    • Locate the camshaft sprocket alignment mark in the 6 o'clock position and install the camshaft sprocket and timing chain
    • Camshaft sprocket bolts and tighten the camshaft sprocket bolts;
      1. Torque to: 26 ft. lbs. (35 Nm)
    • Oil pump
    NOTE: Do not lubricate the oil seal sealing surface.
  1. Lubricate the outer edge of the oil seal with clean engine oil.
  2. Lubricate the front cover oil seal bore with clean engine oil.
  3. Install the crankshaft front oil seal with a suitable seal installer. NOTE: Do not apply any type sealant to the front cover gasket (unless specified). Special tools are used to properly align the engine front cover at the oil pan surface and to center the crankshaft front oil seal.
  4. Install the front cover gasket, cover, and bolts onto the engine.
  5. Install the front cover-to-oil pan bolts and do not overtighten.
  6. Tighten the cover bolts finger tight and do not overtighten. J41480 installation-4.8L, 5.3L & 6.0L 9308kg59.gif

  7. Start the J41480 or other suitable tool to front cover bolts but don’t tighten the bolts yet. NOTE: Align the tapered legs of the tool with the machined alignment surfaces on the front cover.
    Seal alignment tool installation-4.8L, 5.3L & 6.0L 9308kg84.gif

  8. Install tool J41476 or other suitable tool.
  9. Install the crankshaft balancer bolt and tighten the crankshaft balancer bolt by hand until snug but do not overtighten.
  10. Tighten the J41480 bolts and front cover bolts;
    • Torque to: 18 ft. lbs. (25 Nm).
  11. Remove the tools. NOTE: Place a straight edge across the engine block and front cover oil pan sealing surfaces. Avoid contact with the portion of the gasket that protrudes into the oil pan surface. Insert a feeler gauge between the front cover and the straight edge tool. The cover must be flush with the oil pan surface or no more than 0.5 mm (0.02 in) below flush. If the front cover-to-engine block oil pan surface alignment is not within specifications, repeat the cover alignment procedure. If the correct front cover-to-engine block alignment cannot be obtained, replace the front cover.
  12. Snug the oil pan-to-cover bolts in order to position the cover at the pan rail.
  13. Tighten the oil pan-to-front cover bolts;
    • Torque to: 18 ft. lbs. (25 Nm).
  14. Tighten the front cover bolts;
    • Torque to: 18 ft. lbs. (25 Nm).
  15. Install the crankshaft balancer and bolt (See: Crankshaft Damper).
  16. Install the water pump (See: Water Pump).
  17. Fill the engine to the proper level with oil.
  18. Fill the engine to the proper level with coolant.
  19. Test drive the vehicle to confirm the repairs.
6.6L Engine To Remove:
NOTE: The 6.6L engine uses gears in place of a timing chain. For removal and installation, please see the Camshaft and Lifters procedure. This procedure covers the removal of the front cover and seal.
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove the upper intake manifold sight shield as follows:
    • Remove the retaining bolt in the front of the shield
    • Lift up on the front of the shield, then lift the shield off the rear bracket
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    • Negative battery cables
    • Right front wheel
    • Right front fender splash shield
    • Upper fan shroud
    • Fan clutch (See: Engine Fan and Clutch)
    • Drive belt
    • Oil dipstick tube
    • Thermostat housing crossover
    • Crankshaft damper (See: Crankshaft Damper)
    • Crankshaft front oil seal
    • Water pump (See: Water Pump)
    • Camshaft sensor electrical connector
    • Camshaft sensor bolt and sensor
    • Crankshaft Position (CKP) sensor connector, bolt and sensor
    • CKP sensor spacer bolts and spacer
    • 5 bolts securing the upper oil pan to the front cover
    • Bracket bolts and the bracket for the turbocharger outlet coolant pipe
    • Engine front cover bolts
    • Use a suitable seal cutter to separate the front cover from the cylinder block and upper oil pan NOTE: Do not bend the turbocharger outlet pipe.
    • O-ring from the front cover Engine front cover-6.6L engine 9348ng32.gif

    • Oil pressure relief valve from the front cover
To Install:
  1. Clean and inspect all sealing surfaces.
  2. Install or connect the following:
    • Oil pressure relief valve with a new O-ring and tighten the valve
      1. Torque to: 30 ft. lbs. (41 Nm)
  3. Apply a 1/8 in. (2-3mm) wide to 1/16 in. (0.5-1.5mm) high bead of sealant to the front cover sealing surfaces to the engine block and oil pan.
  4. Install or connect the following:
    • New front cover O-ring after lubricating it with engine oil
    • Front cover and bolts and tighten the front cover bolts
      1. Torque to: 15 ft. lbs. (20 Nm)
    • Upper oil pan-to-front cover bolts and tighten the bolts
      1. Torque to: 15 ft. lbs. (20 Nm)
    • Turbocharger coolant outlet pipe bracket and bolts and tighten the bolts
      1. Torque to: 15 ft. lbs. (20 Nm).
    • Camshaft sensor and bolt and tighten the bolt
      1. Torque to: 80 inch lbs. (9 Nm)
    • Camshaft sensor connector NOTE: The CKP sensor spacers are machined with different timing positions. If you have to replace a spacer, make sure it has the same part number.
    • CKP sensor spacer and spacer bolts and tighten the bolts
      1. Torque to: 89 inch lbs. (10 Nm)
    • CKP sensor and bolt and tighten the bolt
      1. Torque to: 89 inch lbs. (10 Nm)
    • Water pump (See: Water Pump)
    • Crankshaft front oil seal
    • Crankshaft damper (See: Crankshaft Damper)
    • Thermostat housing crossover
    • Oil fill tube
    • Drive belt
    • Upper fan shroud
    • Right front fender splash shield and wheel
    • Negative battery cables
  5. Refill the cooling system with the proper type and quantity of antifreeze.
  6. Inspect the engine for leaks.
  7. Test drive the vehicle to confirm the repairs.

Aug 27, 2010 | GMC Sierra 1500HD Cars & Trucks

1 Answer

My 2001 jeep grand Cherokee will not start don?t know why no codes are coming up put new cam sen, crank sen, coil pack, new ecu, new coolant temp sen, it turns over but will not run has injector pulse and...


Timing Chain, Sprockets, Front Cover and Seal REMOVAL & INSTALLATION 2.5L and 4.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt
    • Cooling fan and shroud
    • Crankshaft damper
    • Front crankshaft seal
    • Accessory brackets
    • Front cover
    • Oil slinger
  3. Rotate the crankshaft so that the timing marks are aligned. Fig. 1: Timing chain alignment marks — 2.5L and 4.0L engines 7924pg20.gif

  4. Remove the timing chain and sprockets. To install:
  5. For 2.5L engines, turn the timing chain tensioner lever to the unlock (down) position. Pull the tensioner block toward the tensioner lever to compress the spring. Hold the block and turn the tensioner lever to the lock (up) position. Fig. 2: Timing chain tensioner — 2.5L engines 7924pg19.gif

  6. Install the timing chain and sprockets with the timing marks aligned. Tighten the camshaft sprocket bolt to 80 ft. lbs. (108 Nm) for 2.5L engines or to 50 ft. lbs. (68 Nm) for 4.0L engines.
  7. For 2.5L engines, release the timing chain tensioner.
  8. Install or connect the following:
    • Oil slinger
    • New front crankshaft seal to the front cover
    • Front cover, using a new gasket
    • Timing Case Cover Alignment and Seal Installation Tool 6139 in the crankshaft opening to center the front cover Fig. 3: Timing Case Cover Alignment and Seal Installation Tool 6139 — 2.5L and 4.0L engines 7924pg21.gif

  9. Tighten the front cover bolts as follows:
    1. Step 1: Cover-to-block 1⁄4 inch bolts to 60 inch lbs. (7 Nm)
    2. Step 2: Cover-to-block 5⁄16 inch bolts to 16 ft. lbs. (22 Nm)
    3. Step 3: Oil pan-to-cover 1⁄4 inch bolts to 85 inch lbs. (9.5 Nm)
    4. Step 4: Oil pan-to-cover 5⁄16 inch bolts to 11 ft. lbs. (15 Nm)
  10. Install or connect the following:
    • Accessory brackets
    • Crankshaft damper. Tighten the bolt to 80 ft. lbs. (108 Nm).
    • Cooling fan and shroud
    • Accessory drive belt
    • Negative battery cable
  11. Start the engine and check for leaks.

Jul 30, 2010 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...