Question about 2004 Chevrolet Silverado 2500HD

1 Answer

If i manually pump & bleed the system it will run until i shut it off, then it wont start again, more air in the system (04- 6.6 diesel)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Change the injector seals as they are known to fail causing fuel run back.Allso change the injector leak off pipes.Hope that was helpfull.

Posted on Jul 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diesel pump bleeding


First off you need a good battery or jumper leads as it takes a bit of cranking. You usually don't have to do it at the pump you crack it were the hard line goes into the injector. Back that nut of just enough that you can wriggle the hard line just a little. Then crank the motor over until you see that there are no air bubbles coming out with the fuel. Then tighten the nut while still cranking, after a couple have been bleed the engine will try to run. After the engine is running repeat the bleeding process to each injector again. It does help if you can hook you some low pressure air to the fuel tank and make sure that the fuel has reached the filter and pump before you start.

Apr 03, 2015 | Cars & Trucks

1 Answer

My 2002 chev. diesel truck turns over but wont start, new filter


anytime you change the filter in a diesel you have to bleed the air out of the fuel system. The pump won't auto bleed the fuel system for you. every place in the fuel system that has a flare type connection needs to be bleed, start at the connection closest to the tank, loosen the connection and then crank the engine until you see diesel fuel drips from that connection. Tighten the connection while the engine is still cranking. Move to the next connection that is going toward the engine. Continue on in that manner toward the engine until you reach the injector pump/injector. Once you reach the injector pump be VERY aware that the fuel is at VERY high pressure. Do NOT put your body parts in the stream of high pressure diesel fuel. It could kill or injure you! Once you bleed all the way to the injector pump/ injector, the truck SHOULD start. Do not bleed after the injector pump because of the pressure involved, it is WAY too dangerous.

Good luck!

Dec 22, 2012 | 2002 Chevrolet Avalanche

3 Answers

Why does my ford f350 6.0 diesel start then shuts off and wont stay running.


I have a chevy c3500 with a 6.5 turbo diesel, the times that it has happened

to me was because of a dirty fuel filter or water, most diesel have a bleed off

valve to dissipate any accesss water in the fuel line, on my truck is located

on the right front side of the engine . you bleed it off when the engine is

turned off. good luck

Jul 21, 2011 | 2005 Ford F 350 Super Duty

1 Answer

Ford galaxy 2007 ran out diesel an would not start afterwards tried everthink can u advise me please


Hi James, If any diesel vehicle runs out of fuel it is required to 'bleed' out any air that has entered the system. Have a look on top of the diesel fuel filter housing and there should be a bleeding nipple. It will usually be a ten millimeter or sometimes an eleven. Loosen that until when you pump the plunger on top of the housing, clear diesel passes out. Pump several times, as maybe for the first five or six times the air wont be expelled. Once all the air has been expelled lock the bleeding nipple closed and after preheating crank and start....
Regards Johngee10
Would you mind rating this answer for me?

Feb 09, 2011 | Ford Transit Connect Cars & Trucks

1 Answer

04 sedona wont start after changing diesel filter!


Yes big time ,fit a non return valve in the feed line from the filter to the pump ,you have a air leak somewhere and i would suspect the rubber o ring in the top of the filter housing,its running back when you leave it because of the air leak

Apr 20, 2010 | 2002 Kia Sedona

1 Answer

Diesel 1989 F-250 set too long and will roll over


You may have to bleed the fuel system. There may be a very small air leak in the fuel supply line and after a long time idle, the fuel seeps bac into the tank, leaving an air lock in the pipe. When you go to start, this air makes its way into your injection pump & needs to be bled out before the engine will start. Begin from your fuel filter bleed valve, next the injection pump using the primer pump to transfer the fuel. Next loosen off the injector pipes and crank the engine over until fuel sprays form all the joints. Tighten injector pipes and start. It may run a bit rough for to begin with, but will soon even out. If it doesn't start, repeat bleeding of injectors.

Mar 13, 2010 | 1989 Ford F 250

2 Answers

Mercedes ran out of diesel,put some


Sorry.I am not sure on your model but.If you run a diesel out of fuel,it needs to have the fuel system bled.In the book it will say how.Most common is a bleed valve.Sorry I could not help you more on your car but someone from fixya will..I just wanted to tell you what needs to be done.Sorry I could not help you straight up but wanted to tell you what is needed for your vehicle.Thanks

Sep 27, 2009 | 2001 Mercedes-Benz C-Class

1 Answer

After replacing fuel pump and filt truck wont start with started fuid


If this is a diesel you should not use starter fluid unless the glow plugs and glow plug controller is removed. If this is a diesel you most likely have air in the fuel system.When changing fuel filter on a diesel fill the filter container with clean diesel,screw the top of the fuel filter canister on open the bleed screw and turn the engine over until only clear fuel (no air bubbles)is bled from fuel system. Then you may have to turn loose the connector on the innjectors to bleed more air out of the fuel system.

Jun 15, 2009 | 1994 Chevrolet K1500

3 Answers

How do you bleed a peugeot 206 1.9 diesel fuel system


The diesels I've worked on are bleed at the injectors. You need to loosen each injector in turn and pump up fuel pressure until only fuel comes out, no air, than tighten the fitting up before it back feeds. Repeat this process for each injector.

May 09, 2009 | 2006 Peugeot 505

2 Answers

My 206 1.9 diesel wont start


a diesel engine can only cutout when overheating, loss of diesel fuel and air leak in the fuel system. if you know how to bleed or ask somebody to bleed right after it stall, then start the car, if it starts immediately then it is sucking air.

May 09, 2009 | 2006 Peugeot 505

Not finding what you are looking for?
Cars & Trucks Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...