Question about 1999 Ford Escort

1 Answer

Hi my wheels are rubbing on the wheel arches how hard is it to put new studs in no room for spacers

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

New coil springs you need.Has they are a common fault on them Breaking Check them for damage.And replace.

Posted on Jul 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change front studs on mercury villager


wheel studs are removed by removing tire and wheel , then pound the studs out of hub by hammering on the threaded end until they are out. buy new studs and pull them snug and flush with the nuts and a spacer to take up most of the room between hub and nut

May 20, 2015 | Mercury Villager Cars & Trucks

1 Answer

How to replace front wheel studs on 2011 Kia Forte


If you can find just the studs and not have to buy the whole hub assembly, screw a lug nut on flush to the stud and drive it out with a hammer, make sure its in a position to have room on the back side. Put in new stud and with a few spacers tighten a lug nut to seat it.

Aug 15, 2014 | Cars & Trucks

1 Answer

I got a flat. when removing lug nuts 2 broke off completely. only have three bolts left to hold tire on


They sure can. Some parts stores like Pep Boys carry not only the original lug nuts (19 mm), but also carry the two studs you need. Remove the wheel assembly and with the two broken studs, take a hammer and on the backside, you'll see a hole to line up the back of the stud, and smack it out with a hammer. To install, if you have an air compressor, put each of the new two studs in one at a time an d buy a regular nut with about an inch of spacers over the stud and then zap it in with an impact wrench. Instead of spacers, I used a huge nut. For safety's sake, take care of the two broken studs as soon as possible, for if left too long, the wheel could fly off while driving. Even if you just remove the two broken studs, put the wheel back on and take it to any shop, they'll be able to zap the two new studs in.

Until Then,
I Remain,
Questionably Sane,

~Stillin~

Nov 10, 2012 | 2005 Dodge Caravan

2 Answers

I am working in changing the wheel lug studs on a 99 plymouth voyager i have the hub off and the 5 wheel studs out what is the easyest way to get the studs back in


a spacer and a lug nut are handy to draw the new stud in. *********** such as myself just put the wheel on and use the lugs and the lug wrench. note the lugs are tapered on the business end so if you use them with a spacer, put them on backwards to draw the stud in..

Aug 31, 2011 | 1999 Plymouth Voyager

1 Answer

How to change the wheel studs on the rear end


Wheel is off obviously. Put the nut back on. Pound it with a sledge hammer. It sound pop out. To install, put new stud in and tighten up with nut. It should pull stud in. A Spacer or washers may be needed.

Sep 18, 2010 | 1994 Toyota Pickup

1 Answer

How do I replace the studs on the rear wheel


remove wheel and brake assembly, drive broken stud through back off the hub. Put new stud through hole and use a spacer and an old lug nut to pull stud till its seated in hub.

Feb 27, 2010 | 1993 GMC Suburban

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

1 Answer

How to change stud in rear wheel hub assembly. i need to know how to change the stud in the rear wheel hub assembly, and how do i go about taking it apart


Remove tire and wheel, remove caliper and brake rotor. DO NOT apply the brakes while the caliper is loose. Hit stud you want to replace hard with a LARGE HEAVY hammer to drive it out towards vehicle. DO NOT use a light hammer. It will distort the stud and possibly mushroom the end making it very difficult to remove. Once the stud is loose, you may or may not have enough room to get it out of the hole. You may need to pull the hub loose from the rear suspension to gain more room. Remove the stud. Place new stud in hole. Put a stack of washers over the stud, grease the threads, and using a new FLAT nut with the same threads as the lug nut, tighten until the stud is pulled all the way into the hub. Remove the flat nut, reattach the hub assembly (if you needed to take it loose) and reinstall the brakes.


Sep 28, 2009 | 1994 Ford Probe

1 Answer

18'' rims rubbing on wheelarch


no , solve the problem

Apr 10, 2009 | 2001 BMW 325

2 Answers

Broken wheel stud front left 1992 honda accord


Only if there is an Acsess Hole Directly Behind the STUD'S PUNCH THE Broken SHORT one OUT But there May Not Be Enough ROOM FOR the NEW LONG STUD to go in between the HUB & Rotor Check this FIRST If you see GOOD CLEARANCE TO GET The new STUD in Then just Drive the old one out , and Use A LARGER than Stud Nut Or Washers to Pull New Stud Threw some Before Putting Wheel on. Then Put Wheel on And Tighten Wheel , Retorque after a Few Hundred Miles.

Mar 29, 2009 | 1992 Honda Accord

Not finding what you are looking for?
1999 Ford Escort Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...