Drivers side power windows go down but not up.

was regulator bad? did it work from drivers side switch before you did regulator repair?..if so passenger side switch wiring has issue and is not sending signal through it back to the drivers side master switches.. otherwise you need to pin test for power up power down on drivers side switch and repair that if issue going to the window on passenger side.. (possible pinched at door jam area common)

The power windows on your vehicle are controlled by an electronic control module , as are the power mirrors !
Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Body control module (BCM)
• LR power window switch
• RR power window switch
• Window up and window down relays in each of the rear passenger window switches
• Window lockout switch
• Reversible power window motors in each of the doors (circuit breaker protected)
• LT DOOR CB 25A (System power for left rear window)
• RT DOOR CB 25A (System power for right rear window)

Your best bet , take your vehicle to a qualified repair shop.

If you have a multimeter you can go to the underside of the master panel in the drivers door and independently check the switches for voltage or with no power to the switch assembly check for continuity. Good place to start. If you get continuity to through the switch then you need to check power to the window actuators in the doors.

replace ur power window switches

If they sound like they are trying to do something it's not the lock out switch . But to be sure pulling out the switch an testing for B+ voltage to and from the switch . Plus pull the other door switches to see if they have B+ voltage and good grounds would be the thing to do.. If you don't know how to check automotive electrical circuits your best bet , take it to a qualified repair shop .
Passenger Power Window Operation
The passenger power window switches incorporate window up and down relays. The relay coil feed and supply sides are powered through the RAP fuse supply voltage circuit. The normally closed contacts of each relay is connected to ground. The load side of each of the relays are connected to either side of the power window motor through the power window up and down circuits. The up and down relay control circuits are connected to the normally closed contacts of the passenger window switch. These contacts are wired in series with the power window master switch, through the power window master switch up and down signal circuits and then to ground when the power window master is placed in the up or down position. This allows for the up and down operation of the passenger power window from the power window master switch. The center pole of the passenger power window switch is also connected to ground and will energize the relay when placed in the up or down position.

Driver Power Window Operation
The driver power window is unique from the passenger power windows in that it does not use window up and down relays. The driver power window is operated directly from the power window switch.
The normally closed contacts of the switch are connected to ground and the center pole is connected to the RAP fuse supply voltage circuit. By placing the left power window switch in the down position, voltage is applied to the power window motor left front down circuit and to the power window motor. The other side of the power window motor is connected to ground through the normally closed contacts of the left power window switch through the power window motor left front up circuit and drives the window down.
By placing the left power window switch in the up position the polarity of the motor is reversed and the motor drives the window up.

Has circuit breaker for B+ power
• PWR WDO CB 25A (fuse block) (System power for left and right windows 2-door vehicles. System power for LF and LR windows 4-door vehicles)
• PWR WDO CB 25A (IP wiring harness junction block) (System power for RF and RR windows 4-door vehicles)

Could be passenger door switch .

pull the control switch out n clean contacts or try and spay contact cleaner on them

Try switching the power window switch from the passenger side to the drivers side. Before you do that try with the switch on the up position, wiggle it from side to side. The contacts may be worn and by wiggling it may make contact. Other then that try to park it in side or garbage bag taped to keep rain out till you get it to the shop.
Hint, take it to a Auto window repair shop to replace the switch if it's bad or if the motor is bad. They have more experience to removing the door panels and removing the power window regulator (motor) if that needs to be replaced.
Good luck and hope this helps. 

it is probably the motor in the window

Hello.Try this.while holding the button down on the drivers side window control,hit the door firnly with the bottom of your fist of with your palm.Do this a few times.If the window starts to work,the problem will be the power window motor.

if the fuse is blown none of the windows will work,it sound wierd but all the power to the window motors runs through the drivers side switch. the drivers side switch may be your culprit.to be sure check to see if you have power goin in to the other switches before you replace the drivers side switch.