Question about 2002 Dodge Intrepid

1 Answer

Code for camshaft sensor & crankshaft sensor came up changed both sensors but still getting same readings even after disconnecting negative post & resetting code reader &check engine light wont go off either

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 202 Answers

Your old sensor weren't bad at first, u might have a bad connection, check connection and clean connections with contact cleaner

Posted on Jul 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the crankshaft position sensor on my 2010 srx 3 liters

Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

2 Answers

My truck sonoma gmc 2001 dont past the emission test

Definition of Diagnostic Trouble Code P1345 Audi: Ignition Coil Power Output Stage 3 Short to Ground BMW: Misfire Cylinder 2 with Fuel Cut-Off Buick: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Cadillac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Chevrolet: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Ford: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) GMC: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Isuzu: Crankshaft Position - Camshaft Position Correlation Kia: No SGC Signal (1.6L) Lexus: Variable Valve Timing / CMP Sensor Range / Performance Lincoln: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Mazda: Cylinder Discrimination Signal (from CMP sensor) Mercury: Cylinder Discrimination Signal (Signal From Camshaft Position Sensor) Oldsmobile: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Pontiac: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Saturn: Crankshaft Position (CKP)-Camshaft Position (CMP) Correlation Toyota: Variable Valve Timing / CMP Sensor Range / Performance Volkswagen: Ignition Coil Power Output Stage 3 Short to Ground

Jul 19, 2015 | GMC Cars & Trucks

2 Answers

What does a crankshaft sensor do? what does a camshaft sensor do?

get a HAYNES repair manual, tells you what all sensors do ! the crankshaft sensor sends info to the SBEC, reguarding engine crankshaft position. the camshaft sensor reads camshaft position, sends a coded signal to the SBEC, which uses this info to determine whether the fuel injectors and ignition coils are correctly synchronized !

Feb 14, 2013 | Chrysler Sebring Cars & Trucks

2 Answers

Changed crankshaft sensor, started fine & test drive ok. sat for 3-4 hrs & would not start check engine light on with fault code 340

That code, 340 is No camshaft signal being received by the computer. Might just be the CAMshaft sensor, not the CRANKshaft sensor, that's bad.

Mar 26, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I have a 99 mercury villager, getting a 0340 code. it says its for a crankshaft sensor but vehicle doesn't have one. What does this code mean?

Hi, code 340 is for the camshaft sensor. Below is a test you can run to check the sensor. The PCM is above the glovebox. Do not disconnect or remove the PCM. Just remove the glove box and probe the back of the connector to access the pins indicated in the cam sensor test. Please let me know if you have any questions, and thanks for using FixYa.

1999-00 Vehicles

On 1999-00 vehicles, the camshaft position sensor must be checked with the engine running. If a no start condition is encountered, observe the MIL. With the ignition switch on and the engine off, the MIL should be illuminated. If the camshaft position sensor is functioning, the MIL should go out when cranking the engine.
  1. Run the engine until it reaches normal operating temperature. Leave the engine running.
  2. Using a voltmeter set to the DC range, connect the negative lead of a voltmeter lead to the negative battery terminal or chassis ground.
  3. Connect the positive voltmeter lead to the back of the PCM electrical connector in terminal 44.
PCM pinout


  1. Observe the voltmeter reading. The reading should be 0.3-0.5 volts.
  2. Disconnect the positive voltmeter lead from terminal 44, and connect it to terminal 49.
  3. Observe the voltmeter reading. The reading should be approximately 2.5 volts.
  4. Perform steps 3 through 6 with the engine at 2,000 rpm with the transaxle in park. The voltage readings should be the same.
  5. If the observed voltages are not within specifications, the sensor may be faulty.

The camshaft position sensor is part of the distributor assembly, and must be replaced as a unit. Please refer to Engine Electrical, Distributor Ignition System, Distributor, Removal and Installation for the procedure.

Mar 12, 2011 | Mercury Villager Cars & Trucks

2 Answers

Where is the camshaft position sensor located on a 1997 Oldsmobile Cutlass Supreme 3.1 ?

Removal & Installation 3.1L Engine To Remove:
CMP sensor 93174g24.gif

  1. Disconnect the battery ground cable.
  2. Remove the power steering pump and set aside with the lines connected.
  3. Disconnect the camshaft position (CMP) sensor electrical connector.
  4. Remove the CMP mounting bolt.
  5. Remove the CMP sensor.
  6. Check the O-ring for damage and replace if necessary.
To Install:
NOTE: Lubricate the O-ring with clean engine oil.
  1. Install the camshaft position sensor.
    • Tighten the mounting bolt to 89 in lb (10 Nm).
  2. Connect the CMP sensor electrical connector.
  3. Install the power steering pump.
3.4L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor.
  3. Remove the sensor retainer bolt and carefully pull the sensor from the camshaft carrier. An O-ring seal may hold the sensor in place. Use care not to lose the O-ring.
Camshaft Position (CMP) sensor removal (3.4L (VIN X) engine) 93174g25.gif

To Install:
  1. Installation is the reverse of the removal procedure.
  2. Before installing a replacement camshaft sensor, lubricate the new O-ring with clean engine oil.
    • Tighten the bolt to 88 inch lbs. (10 Nm). Do not over-tighten.
  3. Connect the negative battery cable.
3.8L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor. Camshaft Position Sensor removal (3.8L engines) 93174g26.gif

  3. Remove the retaining screw and separate the sensor from the front cover.
To Install:
  1. Installation the sensor in the front cover.
  2. Tighten the bolt to just 44 inch lbs. (5 Nm). Do not over-tighten. Verify the electrical connector is secure.
  3. Connect the negative battery cable.
prev.gif next.gif

Aug 26, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

P0320 & P1391 OBD codes displayed, found during emissions testing but there are NO engine or driving problems idicated.

P 0320 = No Crank Reference Signal to PCM. No Crank (shaft position) reference signal detected during engine cranking (starting).
P 1391 =Intermittent Loss of either Camshaft Position Sensor or Crankshaft Position Sensor.
Hav you attemtped the "3-Key-Ons" method to see these codes on your digital Odometer (assuming you have one) Turn the Key from Off to On (not start) three (3) times. On the third (3rd) time leave the Key in the "On" position (not start). Look at your Dogotal Odometer (if so equipped). The Codes, one at a time should appear. The Last Code will be "P donE".
If te engine is performing without problems: disconnect the negative side of the Battery and wait at least 5 to 30 minutes. Reconnect the Battery. Re-preform the 3-Key-On's and see if and Codes are now showing.
If you start having Start or Running problems becoming more and more frequent: consider replacing the Crankshaft Position Sensor. If this sensor "fails" you may not get any fire to anything, as this is the signal that is necessary for the PCM to initiate the Firing Sequence. The PCM will not send a signal to even the Ignition Coil to begin.

Jan 07, 2010 | 1998 Jeep Wrangler

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...

P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

2 Answers

Need to change camshaft position sensor 2007 Jeep compass 2.4 eng

Jeep Patriot Crankshaft Position Sensor replacement ...

? 9:09
Jan 15, 2012 - Uploaded by JasonthePCMD
Here's how to replace the Crankshaft Position Sensor (CKP) on a 2008 and newer Jeep Patriot, Compass ...

Jeep Cherokee camshaft crankshaft sensor how to replace ...

? 2:59
May 17, 2012 - Uploaded by unpescad0
How to locate and install a new camshaft and or a crankshaft position sensor. This vehicle is a 2001 Jeep ...

Crankshaft position sensor location - Jeep Patrio

Sep 14, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides