Question about 2005 Dodge Caravan

1 Answer

Other windows won't work on their switches.

Looking for a place to buy either the lock-out switch for the driver's control panel or the entire door control plate. thanks..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

Call up the dealership or carquest. make sure you tell carquest you want an OE direct replacement, and you will most likely need to replace the entire control panel.

Posted on Jul 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

No electric power to left door Fuse and relay are good


Check the wire lume that runs from the body to the door inside a rubber bellow. the wires can break from constant moving and I'm not sure what vehicle you have, but this is a defect for a few vehicles out there the wire can be to short in some cases from cost saving manufacturing. It may be necessary to remove the door panel and remove the harness through the wire opening to be able to move the boot far enough to access the broken wire or even just to check it in some cases.
How I like to repair it, is to put a new wire through the entire pivot point and join it inside the door and body where the wire does not move constantly.

Hope this helps

Mar 04, 2015 | 2007 Saturn ION-2 Quad Coupe

1 Answer

How do i fix power windows on 2001 chrysler sebring


if no door or window switches work in entire car start by checking FUSES , then by spraying compressed air into the switches on the drivers door panel whilst moving switches back and forth. then spray some WD40 or electronic componet cleaner into edges of switches whist moving switches hoping they come back to life. then pulling open drivers door rubber harness cover where it enters car. look for wires in the loom that are cracked and broken. this is likely.as wires bend each time door is opened. then remove drivers door panel and test then remove loom connector from door frame and use OHM /volt meter to find broken wires or switches in drivers door problems in drivers door. check for voltage at window motor first. . buy whole new door panel with wiring harness and switches at Pick n pull. if that does not work ..buy a haynes manual and look at wiring schematics. NEVER GIVE UP. NEVER BUY NEW PARTS.

Aug 31, 2014 | 2001 Chrysler Sebring

1 Answer

Only the drivers window works, first it was the real ones and now the pass. won't work at the door switch


Could be individual switches or the rear may have child safety locks on them--the clue will be usually you cannot open rear doors from inside the vehicle---it (the child locks) will in many cases stop rear windows from working----consult the owner manual or look at inside of rear doors for the slide switch at each door under and near the rear of the armrest.

Dec 10, 2012 | 2000 Mercury Sable

1 Answer

Just bought 2000 Ford Focus SE sedan.Neither rear window will operate from drivers door or from rear door switches.Fuse is good. Any other places to look without tearing into door panel?


Look to see if there may be a child safety feature. Not allowing passengers to roll their own window down. The drivers window switch is the master switch that controls all others. For example, if drivers window switch was disconnected than none others would work. Some vehicles it is not necessary to remove door panel when removing the master control switch. I'm not sure if you are one of the ones that doesn't have to do that.. good luck.

Jul 11, 2010 | 2000 Ford Focus

4 Answers

Window problem


Might want to check the doors with the problem windows for a broken wire from the door to the door jam.

The window lock switch is a single circuit to all the other windows, so if there was a problem with it, none of the window controls would work ( but the driver's side would still operate them ).

The other place to check for a broken wire is the driver's side door to a-pillar harness. The circuits for the other windows run through the driver's side switch. Could be a wire in the driver's side door harness.

The other item could be the driver's side switch, the contacts will get carbon built up on them, and the windows will not operate anymore.
This is what mine looked like when the driver's side window stopped working ( lower left hand corner of the picture is the driver's side window switch, note the carbon build up on the contacts )
ccfb7fb.jpg

I would start with checking for broken wires, by metering the window switch for power.

The back passenger's window switch should be getting power & ground on the white w/ yellow stripe wire and the tan w/ light blue stripe wire.
in the "at rest" position on the driver's side switch, these are supplying ground to the power window, and power is being applied to the other side of the motor ( depending on direction of travel ).
792a56e.jpg

Apr 05, 2010 | 2004 Ford F150

2 Answers

I have a 2004 Jeep Grand Cherokee Laredo. The door locks and windows don't work from driver's door controls. The dash lights are dim with the headlight turned on. The rear interior lights only work when...


Hi,

Sorry to hear your having this problem.
The door jamb switch will not usually cause this much of a problem. As you may be aware of electrical problems can be easy or they can be rough.
Let's assume for the situation here it is an easy one.

There are several connections in the door that can effect the entire circuit.
If the door locks work from the passenger side and not the drivers side - you will need to pull the door panel from the car to have a look see.

This is not as hard as it looks if you use the right tools.

removing the panel requires you remove the proper screws and the pull handle/arm rest. there is a removal tool for the outside of the door panel where it meets the door. I suggest you invest in one to save the value of your auto- no rips in the door panel = more money when selling.
Once you get the 'DOOR PANEL REMOVAL TOOL' - please go to your local Advance Auto - Auto Zone - Etc - and get one - -
slip this tool between the door panel and the metal it is attached to. REMEMBER - if the door panel resist - there are MORE things to loosen and here is where you become a pro - - just be PATIENT and think of ALL the money you're saving and remove every screw and panel tab etc -
Remove the panel and set it aside.
Get GOOD NEW BATTERY flash light and shine it into the door with the window up - this will show you any frayed wires etc.
make sure the wires going into the control for the windows - doors is solid and tight - and with that hooked up [ brace the panel and have a helper hold it into place as they will not work unless hooked up for testing.
If nothing changed - remove the control and replace it.

Pictures as you remove this will help A LOT - when you go to replace it -
I STRONGLY - - STRONGLY recommend someone else to take the pics as you remove things - it will help you - and yes us pros do this all the time
Best of it

Gary
Please vote me up
RICESKI

Mar 20, 2010 | 2000 Jeep Grand Cherokee

2 Answers

91 4runner power window fuse s are good but none of the door windows work and only the passenger power door lock works


replace the power window master switch and chances are the lock actuators are bad. replace as neccessary. happy holidays

Dec 28, 2009 | 1991 Toyota 4Runner

1 Answer

Driver side power window switch not working with window in open position. . How do I remove the inside panel or switch control panel on drivers side?


From the inside of the car pull out the handle that opens the door and remove the screw/s. The take off the entire door panel by taking a flat blade screwdriver and prying up along the perimeter of the panel. Usually 5 or 6 plastic snap in screws hold the panel in place. Unplug the switch panel.

I had a similar problem and it turned out to be the window motor. Google window motor and vehicle type to find less expensive aftermarket motors.

Diane

Oct 18, 2009 | 2002 Ford Explorer

1 Answer

2001 Civic SI (EX american) remote lock problem


OK - the master switch is the switch panel on the drivers door that controls every lock and window of the car.
If you are pressing LOCK and all the doors LOCK except the driver's door - the Locking Actuator's Solonoid has failed.
You cannot replace just the solenoid - the entire thing is replaced as a unit.
It looks similar to THIS....
78d9067.jpg 6343dcf.jpg
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 14, 2009 | 2001 Honda Civic

Not finding what you are looking for?
2005 Dodge Caravan Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...