Question about 2000 Pontiac Sunfire

1 Answer

How do I program my keyless remote for my 2000 Pontiac Sunfire?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote.Go see a locksmith or a gm dealer.

Posted on Jul 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i program the keyless remote to my 2000 Pontiac Grandprix


some of them you cycle ign 10 times then push lock unlock on remotes

Jun 18, 2010 | 2000 Pontiac Grand Prix

1 Answer

2006 pontiac g6 keyless remote programming


must take FOBs to dealer for programming.... there is no other way and it's cheap (you can take any number of FOBs and it's still a flat rate (~$40)

May 20, 2010 | 2006 Pontiac G6

1 Answer

I have a problem with opening car doors with remote for 1997 pontiac sunfire. I noticed that when you are in the car and you activate the open and close switch from drivers side the locks at the rear open...


Try this procedure...

KEY FOB PROGRAMMING INSTRUCTIONS
Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old & the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If u program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver is seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle is doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body & Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open & then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If u do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press & hold the transmitter LOCK & UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body & Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Hope this help (remember comment and rated this).

Apr 16, 2010 | 1997 Pontiac Sunfire

1 Answer

I tried the program instructions for my keyless


Here's what I found. Go to this page and select 2006 Grand Prix - http://www.programyourremote.com/classified/Browse.asp?cid=273
You can't program I guess, sorry

Dec 18, 2009 | 2006 Pontiac Grand Prix

2 Answers

Unable to program my keyless remote for 2000 chevy malibu


take key fob to a cparts store , most have a tester on the counter

Jun 08, 2009 | 2000 Chevrolet Malibu

2 Answers

Keyless entry wont work after battery died


stand at the vehicle and push and hold the lock and unlock buttons till the horn chirps to resync the key fob

May 03, 2009 | 2002 Pontiac Sunfire

1 Answer

Remote Key for 2004 Sunfire Pontiac


take vin numbers to a pontiac dealer along w/ bill of sale and you will have your key in minutes. hope this helps

Aug 25, 2008 | 2004 Pontiac Sunfire

1 Answer

Keyless remote programming insyructions


If the remote is generic you will need the factory remote to "clone" the signal to the new remote.

With your oem pontiac remote you may need to visit any GM service center to have the remote set to the cars receiver. There are literally 100,000 different variables GM uses to ensure one remote can't work the wrong car. A typical key programming will run you between $30-$60 depending on how much greed the technician has. Some good technicians will do this job for free simply to make a customer happy so you may wish to call around.

Jun 29, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
2000 Pontiac Sunfire Logo

Related Topics:

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...