Question about 2000 Jeep Grand Cherokee

1 Answer

2000 grand cherokee water pump

How do you get the fan blade off?

Posted by on

  • ricmcd06 Jul 24, 2009

    i am changing the water pump and cannot get it off until the fan blade is out of the way.

  • ricmcd06 Jul 24, 2009

    i am changing the water pump and cannot get it off until the fan blade is out of the way.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,627 Answers

You should be able to replace the belt without removeing the rad fan.you will have to feed it around the fan until it is on the pulley side.

Posted on Jul 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the water pump and radiator on our 2000 jeep grand cherokee 4wheel drive 4.7L. I am having clearance problems between the mechanical fan and the back of the electric fan.


it could be that the shaft on the new water pump is longer than the one on the original water pump, will need to measure it & see if there is any difference......cheers.

Sep 17, 2011 | 2000 Jeep Grand Cherokee

1 Answer

We have replaced the water pump, theromstat and temp sencer, still pushes red line when stopped in traffic.


do you have a electric fan on your vehicle, if so, check the fan relay , located in the power distribution box, under the hood , on the drivers side. "if you do not have a electric fan, check the fan clutch , located between fan blade and water pump.

Jun 30, 2011 | 2000 Jeep Grand Cherokee

1 Answer

I have a 2000 jeep grand cherokee and its just started overheating after the fan broke, we replaced it then replaced the fan switch relay but not sure what else it could be.


you also have a thermostat that mounts in one of the pipes at the top of the engine and there is also a temperature sensor the other problem is you could have a bad water pump lift your hood and see if there is any rust or liquid coming out of the water pump where the pulley is if the pump dosent circulate water you could over heat

Mar 10, 2011 | 2000 Jeep Grand Cherokee

1 Answer

Removing the harmonic stablilizer, fan blade from the water pump shaft


it has a left handed thread if i remember rightly ,and i couldnt get it to undo so i tapped it with a small chisel and big hammer ,hey presto it started to undo with the spanner then ,iam sure it was a 32mm spanner but ??

May 31, 2010 | 2000 Jeep Grand Cherokee

3 Answers

Fan at radiator of cherokee is loose and banging


No it sounds like you have a bad water pump..

Feb 03, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Overheats at low speeds and idle. Fan working ok


sounds like the water pump perpelar blades have worn off,that is what I would check first.If the coolant lever is good,and no air in the cooling system,then pull the water pump,and check it out.

Oct 05, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Serpentine belt diagram for 2000 jeep grand cherokee 6 cylinder


Around the outside of power steering pulley,under idler,over a/c comp,around alternator,over fan pulley, around crank pulley, over water pump. The backside of the belt contacts the idler, fan and water pump.

Sep 28, 2009 | 2000 Jeep Grand Cherokee

1 Answer

How do i replace my water pump


it is located in the block of the engine. Follow your radiator hoses to the block. The top is where your thermostat is and the bottom is where your water pump is. ------------- start by taking off the shroud around fan blade, bolts on top of radaitor. pop in plugs on bottem. Shroud will slip by blade with radiator loose. Loosen bolts from tensioner and slip fan belt off Use a ratchet to take four bolts off of fan remove it set aside. Loosen all bolts from power sterring pump only one will have to be removed. From there you can slip out and replace water pump without much trouble. ------------ this will help.

Sep 23, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Changing the water pump on 2000 Jeep Grand Cherokee V6


WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Jan 10, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...