Question about 1992 Chevrolet G20

1 Answer

Bolt torque spec- 1992 Chevy G20 van

I need to know the torque spec for the torque convertor bolts for a 1992 Chevy G20 van, 700R4 trans

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

24-26 ftlbs

Posted on Jul 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the tranmission pan unscrewed to change Gasket 1984 chevy c10


If you are going to change the gasket, you should also change the filter at the same time, especially if it hasn't been done recently. You will need a large drain pan to catch oil in because there is no drain plug. Remove the bolts down both sides of the trans pan, 1/2" I believe, and loosen the back ones 3 or 4 turns. Loosen and slowly remove the bolts on the front of the pan because oil will start to drain from there. Once the oil has drained remove the back bolts and drop the pan. clean it out good and check for "stuff". It's normal to see silver filings in the oil but an excessive amount or actual pieces indicate a problem. Two screws should remove the filter. Replace it and put the new gasket on and set the pan in place. Bolt it on. Torque specs for these bolts are 12-13 ft.-lbs for the Turbo 350 and 400. The 700R4 is torqued to 18 ft.-lbs.

If you have trouble getting at the rear bolts on the trans pan, you may need to unbolt the trans mount and lift the tailshaft a little with a jack to get enough room to get it there. Be gentle doing it.Hope this helps.

Sep 25, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

Bad starter on a 1992 g20 chevy van . Would like to replace starter myself


Then do it! make sure you disconnect the battery before starting job, Make notes or draw a picture of where wires go, remove bolts (sometimes they also have a bolt on a right angle bracket on nose as well as on mount)
When re-installing wires, make sure none from one post are touching other post and do not overtighten...solenoid cover is plastic and will break. if you have a code protected radio, use a "setting saver" plugged into lighter outlet or know the code before battery is disconnected
good luck!.

Dec 14, 2009 | 1992 Chevrolet G20

1 Answer

Im looking for head bolt and rocker arm torque specs for a 1995 chevy G20 van with the 5.7 liter engine


the way to get these specs it to spend the 14 bucks on a chiltons book for your model truck.hate to say that. i have about 20 chiltons books they are worth it trust me on this.they will give you specs diagrams and how too's of your truck.you can get them at adap,napa,carquest,autozone,and pep boys, saves time and its good for quick reffference while working on projects on your truck

Nov 28, 2009 | 1995 Chevrolet G20

1 Answer

What are the torque specs for intake and head for a 1992 c 1500 chevy silverado. I need to know the torque specs for intake and head for my engine


For 1988-1995 4.3L,5.0L and 5.7L intake manifold bolts are torqued to 35ft.lbs.Start with center bolts on each side moving out finishing with the bolts in the front of the motor and the back

Oct 24, 2009 | 1992 Chevrolet C1500

1 Answer

700R4 transmission diagrams needed


Im needing and exploded view of the inside of a 700 R 4 transmission

Jul 31, 2009 | 1992 Chevrolet G20

1 Answer

I have 700r4 trans. shifts from 1to2 but won't shift 2 to 3


Since it still moves in first and second, likely the end-play inside the transmission is enough to cause a shaft seal to bypass pressure. (internal thrust surfaces or washers worn). Being that old, it most likely is in need of a rebuild. If that's the first time you've needed to do trans work, you have gotten your moneys worth there!!

Jul 22, 2009 | 1992 Chevrolet G20

1 Answer

What size allen bolts are on the front brake


I think they are a t30 Not sure exactly, But ask the auto parts guy at the store he will be able to tell you exactly

Jul 12, 2009 | 1992 Chevrolet G20

1 Answer

700R4 automatic transmission won't upshift


Check the TV cable, it may need to be adjusted or it may be binding and jammed. There could also be a problem with a broken governor gear since it's made of plastic, driver's side near the back of the main case under a round case. If it's is the governor gear replace it with the roll pin and filter just to make sure there are no broken parks that may have been caught by the filter. Good luck and hope this helps. 

Jul 03, 2009 | 1992 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...