Question about 1999 Ford Taurus

1 Answer

I have broken motor mount in my 1999 ford taurus.

I have broken motor mounts in my 1999 ford taurus. i bought the chilton repair book, but it still isnt helping. where are the motor mounts located? and how do i get to them? diagrams please?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

Here's a link that may help you.

Posted on Aug 06, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

04 ford taurus ran hot on me

The Internet, though, has a large number of web sites where
you can buy service manuals and schematics from bookstores,
publishers, and other collectors. Here is just a sampling of
what sites are out there:

Chilton Repair Manuals

Factory Automanuals

Factory Auto Manuals is specialist dealer in quality used factory car...

Haynes Publishing
Haynes auto manuals
Haynes is the information resource for the DIY enthusiast

Vintage Books
Vintage books com Rare used and out of print books
Vintage books com Rare used and out of print books


Jan 25, 2013 | 1992 Ford Taurus

1 Answer

Broken motor mount need to know where they are on 1999 ford taurus

The mounts are to either side of the motor on the bottom, they look like blocks with rubber in them.

Jun 23, 2011 | Ford Taurus Cars & Trucks

1 Answer

What is the fuse diagram for a 1995 Ford Taurus? I do not have a owner's manual.

I recommend going to the Auto Parts store and paying $19-$25 for a detailed 1995 Ford Taurus Chilton's repair book. It will show fuse box schmatics and wiring diagrams a long with everythnig else you need to maintain your car.

Jan 27, 2011 | 1995 Ford Taurus

1 Answer

I need to replace the existing starter in my 2003 Ford Taurus wagon. I know that I have to jack the car up in order to remove the old starter. What I don't know, is how many bolts need to be removed...

Because of the Variety of mounting methods there are 2 to 4 bolts that should be visible as you look at the starter itself. Not counting the wiring connections. If this a sideways mounted motor with the Starter mounted on the front of the motor there will be 2 bolts holding it in place. If the motor is mounted regularly with the transmission extending under the vehicle the starter in on the rear of the motor near the firewall and will have up to 4 bolts holding it in place but most likely no more than 3. I would recommend getting a Haynes repair manual on the vehicle for more detailed instruction on removal and installation. This manual or a Chilton's manual are both available at the major Auto Parts stores and are fairly inexpensive.

Aug 28, 2010 | 2003 Ford Taurus

1 Answer

I need a step by step guide to changing my power sterring pump on my 1999 ford taurus 3.0 dohc v6

Rather than typing the directions from memory.
The best advice I can you is, stop by the library and
check out a chiltons/moter or mitchells repair manual. Any of these books will give you all the step by steps and diagrams, you will need to do the job.
Hope this helps. Good luck.

Jan 26, 2010 | 1999 Ford Taurus

1 Answer

How do you change the motor mounts on a 1999 ford contour v6 (or 1999 mercury cougar) engine. The two bottom mounts on the front and back rails are broken.

I've seen people lift the motor slightly and stuff a chunk of a tire in there. Its actually better in some cases than OEM. You wont need to disconnect the motor from the trans. easiest way is to take the hood off and lift the motor just enough to get the old mounts out. There isnt anything real complex about a mount. Like I said... lots of people make their own. Probably more people pay the big bucks to have a pro do it and have genuin OEM part put in, and then pay with their credit card.

Oct 02, 2009 | 1999 Ford Contour

1 Answer

I need to install lower ball joints, how do you do this? Are there any diagrams?

Can't "safely" explain the whole process here...
Go to your public library (you have a card, right?).
The "Reference Section" has several car repair manuals (Motor's, Chilton's, etc.).
Find your book and photo copy the pages you need using the Library public copy machines (15 ~ 25 cents per page).
The books are full of pictures and numbered step-by-step instructions. They even give the part number for any special tools. You will need one special tool... a ball joint yoke chisel (another expert will actually know the real name of the tool - $8 AutoZone).

Sep 22, 2009 | 1999 Ford Taurus

1 Answer

I need the a/c system diagram for a 1999 Ford Taurus, 3.0

N/A...sorry, I doubt even a Chiltons automotive manual has it...check AutoZone/NAPA for book.
Good Luck

Jun 14, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

1,418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides