Cars & Trucks Logo

Related Topics:

2008 v8 Cadillac srx serpentine belt replacement.. Do I have to remove the fan first?

5 Related Answers

Anonymous

  • 3 Answers
  • Posted on Jan 25, 2009

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Ad

Anonymous

  • 1 Answer
  • Posted on Dec 15, 2009

SOURCE: Changing fuel filter on 2004 Cadillac SRX

If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.

Anonymous

  • 10 Answers
  • Posted on Apr 13, 2010

SOURCE: Starting disabled remove key

VEHICLE ANTI THEFT SYSTEM HAVING PROBLEMS

Kravcar

Mark Carrington

  • 192 Answers
  • Posted on Apr 28, 2010

SOURCE: replacement sequence for serpentine belt for a 96 cadillac devill

Assuming you have the Northstar engine

1302403.gif

Anonymous

  • 1190 Answers
  • Posted on Aug 17, 2010

SOURCE: what is the firing order of 2004 V8 4.6L cadillac

firing order as follows:1 2 7 3 4 5 6 8 hope this helps 4.6 northstar

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

I have a 2012 Cadillac SRX and am about to replace alternator but I am having trouble getting serpentine belt off

release the tensioner pulley
it will be near the top of the engine and will have a 1/2" square hole in it
use a strong arm bar 1/2 " drive and push down or pull across

that releases the tension so that the belt can be removed easily
0helpful
1answer

2008 cadillac srx fixing or replacing light bulbs rear license plate

You might be able to access it if you stick your hand up inside the rear of the bumper.
0helpful
1answer

The ingene makes a noise like a cat

It may be a dirty or worn serpentine belt. water in a spray bottle sprayed directly at the belt where the noise is coming from will help diagnose the cause. Noise will be gone for a short while if it is the cause.
0helpful
1answer

Transmission fluid replacement 2004 Cadillac SRX v8 northstar

My 04 CADILLAC SRX AWD V8 is saying 18% transmission life left..do I need to change the fluid all together or can I add some more to fill it up...I have no leakage????
Can someone please help me????
0helpful
1answer

Change turn signal bulb 2008 srx

Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.
1helpful
1answer

Where is cylinder #6 located on a 2004 cadillac srx v8 4.6L AWD

Looking at the front of the engine from where the serpentine belt is at, # 6 right side, back cylinder, right side 2-4-6, left side 1-3-5.
Not finding what you are looking for?

753 views

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...