Question about 1994 Ford Ranger Supercab

1 Answer

Changing the rear lens in a 1994 ford ranger - it is on the driver's side, and I have removed the two screws, what else is there

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

It should just pop out but it some time gets stuck though.

Posted on Jul 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a turn signal lense?


You can't replace just the lens, you can only replace the whole housing. You should be able to remove several screws to get it off the vehicle, then unplug the light connectors from the housing.

Jul 28, 2014 | 1994 Ford Ranger Supercab

1 Answer

Where are the brake line couplings located on the drivers side rear of a 1994 ford ranger 4wd extended cab?


the couplings are usually set in the frame before the gas tank or after the tank if its not one solid line from the master cylinder.the main one is sitting on the top or top side of the differential assembly and is easily seen.

Jul 06, 2011 | 1994 Ford Ranger Supercab

1 Answer

How do you change the front turn signal bulb on a 1994 ranger


Hi there,

Here are some few tips to help out. Firstly, remove the screws retaining the headlight and trim assembly. Then carefully rotate the headlight and trim assembly away from the vehicle, rotating the inboard side away from the vehicle. Remove the side marker, parking and turn signal bulbs and sockets from the headlamp and trim assembly. They can be removed by turning them. If you are replacing a lens, remove the retaining screws for the lens to be changed and remove it from the headlight door.

When removed, install the removed lens assembly. Then, install the bulbs and sockets and install the headlight and trim assembly. Make sure you check the operation of the lights.

Best of luck...

Jan 16, 2011 | Ford Ranger Cars & Trucks

1 Answer

How do you replace the turn signal light in a 93 ford ranger


The procedure is as follows:---First you need to open the hood and twist the bulb socket out from the lens.1)Remove the screws retaining the headlight and trim assembly.
2)Carefully rotate the headlight and trim assembly away from the vehicle, rotating the inboard side away from the vehicle.
3)Remove the side marker, parking and turn signal bulbs and sockets from the headlamp and trim assembly. They can be removed by turning them.
4)If replacing a lens, remove the retaining screws for the lens to be changed and remove it from the headlight door.
--------- Thanks.Helpmech.

Dec 15, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Replace heater core


    A heater core transfers heat from a 1994 Ford Ranger's engine to the passenger compartment by running hot radiator coolant through a serpentine of tubing. Air blows past the hot fins of the heater core and into the truck cab.

    The hoses running to and from the heater core must be removed from the engine compartment, but the core itself is accessed from inside the passenger compartment, on the driver's side next to the center console.

    1. Turn off the engine, open the hood and remove the battery cable from the negative terminal. Make sure the engine is cool.

    2. Attach a 3/8-inch interior diameter hose to the drain outlet on the bottom rear corner of the radiator on the driver's side, and place the bottom end in a resealable plastic container. Turn the drain valve (located above the drain outlet) counterclockwise with a pair of pliers. Drain the engine coolant into the resealable container, then close the valve by turning it clockwise. Remove the hose from the outlet.

    3. Loosen the hose clamps on the radiator hoses where they attach to the heater core on the firewall. Remove the hoses.

    4. Unscrew the screws holding the underdash cover in place on the driver's side of the passenger compartment. Remove the underdash cover.

    5. Unscrew the four screws on the cylindrical heater core access cover and remove it. Remove the heater core by pulling it down and toward the rear of the vehicle. Replace the unit with a new heater core.

    6. Reinstall the heater core access cover and screw in the retaining screws. Replace the underdash cover and screw it into place.

    7. Replace the radiator hoses on the heater core in the engine compartment. Tighten the hose clamps. Add coolant until the level is between the minimum and maximum marks on the reservoir.

    8. Replace the battery cable and start the engine. Check the system for leaks.

Dec 05, 2010 | 1994 Ford Ranger Supercab

1 Answer

How do you adjust the parking brake on a 1994 ford ranger,manaul trans,4wd


Start by adjusting up the rear brakes, if those are tight and you still want to tighten up the parking brake running down the driver's side, outside the frame are the parking cables. somewhere around the back of the cab/front of the bed should be a plate with 2 cables and a bolt. tighten the bolt/nut up to make the parking brake tighter

Oct 04, 2009 | 1994 Ford Ranger Supercab

1 Answer

1997 FORD RANGER. HOW DO YOU ACCES LEFT REAR SPARK


You have to remove the front passenger side tire and access it from underneath.

Aug 21, 2009 | 1997 Ford Ranger SuperCab

1 Answer

1994 ford ranger 2.8 v6 engine automatic 4 wheel


That could Be caused by the TFI module Located on the side of the distributor its grey module that requires a special tool to remove the two screws

Aug 04, 2009 | 1984 Ford Ranger

1 Answer

How do you remove the lens to replace the bulb on tail light on 04 ranger . It only has 2 screws & some kind of pop rivet.


remove the 2 screws-NOW GENTLY PULL/PRY with preferably your fingers or if not a flat head screwdriver the part of the lens that is farthest from the screws and like you mentioned there is something similar to a stud/ball that "holds" the other side of the lens.many tailight lenses nowadays are like this.

Jul 09, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

Cannot open the rear lamp to replace globe


There are 4 screws to hold the rear lamp on. Two are in the lens at the side...the other two are seen when you lower the tail gate.
Hope this helps.

Aug 18, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...