Hi I had the engine block and head re-done. now the engine light does not go off. can you assist please.

The correct head and block settings for an Isuzu KB 260 4ZE1 petrol engine will depend on the specific model and year of your vehicle. It is generally recommended to refer to the manufacturer's specifications or a repair manual for the specific head and block torque settings for your engine.
In general, the head bolts on an Isuzu 4ZE1 engine should be tightened in a specific sequence and to a specific torque specification. The block bolts should also be tightened in a specific sequence and to a specific torque specification.
It is important to follow the manufacturer's specifications and torque the head and block bolts to the correct specification to ensure proper engine function and to prevent damage. If you are unsure about the correct head and block settings for your engine, it is recommended to seek the assistance of a professional mechanic or refer to the manufacturer's specifications.

some settings here on this page with a pretty picture side bar! Full service manual though. Click CONTENT.
https://zinref.ru/avtomobili/Chery/155_00_00_Chery_S11__Chery%20QQ_manual_english/248.htm

..

Hi. Thanks for your question. You can follow some steps and reset the service spaner light on 2015 cher J3. For assistance you can visit https://www.reliable-store.com and download the entire workshop manual which includes all the information along with the diagrams for better understanding. Good day!

Chery Tiggo 2.0 liter engine.
cylinder head torque sequence: 7 6 2 4 9 .......................................... 10 3 1 5 8
Is's done in 3 stages 1st stage 45 Nm......
2nd stage 90 degree turn, or a 1/4 turn......
3rd stage 90 degree turn, or a 1/4 turn.......

Camshaft bolts inlet and exhaust share the same torque settings 120 Nm

Cylinder head bolts MUST be replaced.

Main bearing cap Bolts: 1st 45Nm.......
2nd 180 degree turn, or 1/2 turn.......
Connecting Rod Bolts 1st 25Nm......
2nd 90 degree turn or 1/4 turn

Lower cylinder Block bolts 23 Nm........
Camshaft bearing cap bolts: 11Nm

A CHINA CAR?
800cc engine.
SQR372 DOHC 12V I3 - 38 kW (51 hp) at 6,000 rpm, 70 N·m (52 lb·ft) at 3,500 rpm

why not contact Chery and get the FSM, if serious on repairs
why not get the book.? think of it as part of car ownership, for life.
do you know it must be tensioned, and done right>?
not just timed, it must be all done right or it fails FAST. pronto.

http://cheryengine.en.gasgoo.com/auto-products/18487.html

google does not find a free FSM, only on 472

most I have seen are on a flat spot where the head sits on the block.. its stamped on there..

Elroy Vincent Schenk

when a question is historically 10 years and 2 days old, it is better to post your own question as a new one.

Chery QQ Service Manual [Page 23] - Cylinder Head

ManualsLib https://www.manualslib.com > ... > QQ > Service manual
(Measured valve clearance -0.25mm). ? Exhaust valve. Select gasket thickness = Unload thickness +. (Measured valve clearance -0.25mm). [Reference]. The 32 ...
..

Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

good morning and welcome to fixya
how hot is the engine temp reading? you need to make sure that the water pump is actually pumping you should be able to see the coolant moving past the radiator cap if you remove it. is the vehicle losing coolant? you might want to take the vehicle in and have a block test done on it, this will check the hydro carbons to see if you possibly have a blown head gasket or a crack somewhere that there shouldn't be. please let me know so i can assist you further. thank you again



please rate this solution??