Question about 1996 Jeep Cherokee Country

1 Answer

Jeep turns over but won't start.Replaced very worn plugs. Suspect the crankcase sensor.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 193 Answers

It takes spark, fuel, and air to run.Is there spark? would need more info...

Posted on Jul 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 Jeep Grand Cherokee Laredo. I replaced the crankshaft censor, the camshaft sensor, and removed the alarm system module. It will not start. I also replaced the distributor cap rotor etc.


dont just replace parts and hope--u must target the area--a data stream run w factory gear is really helpful--a code reader is usually not enough-----the module u took out is connected to ignition----inspect coil-plug wires--ignition module--distributer cap may be worn inside--look for any loose wiring in engine area----may need a fuel pressure test--regulator and pump cud be worn---basic spark and fuel hardware are the weakest links

Nov 09, 2014 | 1995 Jeep Grand Cherokee

1 Answer

My 89 jeep cherokee won't. Start it will turn over


what motor? is the coil producing spark?? If so, check the fuel pressure, if the fuel pressure is low drop the tank, repace the pump and also replace the filter (located on the frame forward of the tank). If the coil is not producing spark, check for shorts or opens in the circuits as well as the IGN fuses. If there is NO fuel pressure at all check the fuel pump fuses and make sure the fuel pump is plugged in and there are no opens in the circuit

Apr 07, 2012 | 1989 Jeep Cherokee

1 Answer

Oil in maf sensor


POSIBLE CAUSES:
Over filled crankcase.
Excessive engine blow by caused by worn rings or a scored cylinder wall.
Plugged PCV positive crankcase ventilation system valve or collapsed hose.

Apr 06, 2012 | 2001 Ford Windstar

2 Answers

I have a 2002 Mercury Sable w/DOHC that was drove through flooded intersection last week & stalled. The water was about 2-3 feet deep. I've replaced oil, filters, spark plugs & dried out...


when car won`t turn but clicks then the ( brushes of you starter are worn may be the man who replace used the old brushes ) its very simple thing but will get your car to start
but you didn`t mention anything about fuses and relays if you haven`t replace them all then replace relays/fuse first
you welcome any time sir .

Jun 14, 2011 | 2002 Mercury Sable

1 Answer

I have a 1994 Jeep Grand Cherokee Laredo 6 Cyl. The vehicle was kind of running rough on idle. Take in consideration that I have replaced the spark plugs, spark plug wires a while ago. So I decided to...


CHECK ASD RELAY THAT IS AUTOMATIC SHUTDOWN RELAY IN THE POWER DISTRIBUTION CENTER UNDER THE HOOD IN ENGINE COMPARTMENT.IF ASD RELAY GOOD PROBLEM COULD BE CAMSHAFT SENSOR IN THE DISTRIBUTOR.TO SAVE TIME AND MONEY HAVE JEEP SCANNED FOR CAMSHAFT SENSOR AND CRANKSHAFT SENSOR FAULTS.

Apr 23, 2010 | 1994 Jeep Grand Cherokee

4 Answers

2006 Jeep Wrangler won't start


First, make sure you can turn the engine by hand. If you can't then the starter can't turn it either. Have someone else turn the key and look for the source of the click...may be a relay. Go over the starting circuit with a volt meter. Check for power at the starter main terminal and then with the key turned to "start" check for power at the trigger terminal on the starter. Check battery voltage and check relay operation.
You have a neutral safety switch on the transmission if its an automatic and a clutch switch if it's a stick. Check them as well. Make sure battery grounding on fender and block are also clean and secure.

Oct 01, 2009 | 2006 Jeep Wrangler

3 Answers

Not getting spark when engined turns


Suspect failed crank sensor. Sensor is located on left rear of engine and mounts into the bell housing fro the transmission. Common problem for this vehicle.

Apr 11, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Cherokee Country Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...