Question about 1999 Ford Crown Victoria

2 Answers

CVPI fresh out of the auction. High beams don't

CVPI fresh out of the auction. High beams don't work. Probably cut out when police sirens and strobes cut out. Any ideas where to look?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Prior to 2003 CVPI, check for a cut green/white wire running to both lights..

2003 + Check the wig-wag connector in front of the grill to make sure the clip is connected so it allows normal operation

Posted on Jul 24, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Headlamp switch

Posted on Jul 23, 2009

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My high beams will not come on, the low beams work great, is it possible that both bulbs burned out. The high beam indicator works but the high beam lights don't, what could it be?


Yes, it is possible both are burned out. I recall a police car coming in for no high beams, after some diagnostics I found both bulbs out.
The vehicle probably uses relays under the hood (year, make, model???) if it is one relay it could have bad contacts. Have someone turn beams on and off, listen under hood (key on, engine off) for a clicking sound, this will be high beam relay.

Nov 22, 2013 | Cars & Trucks

1 Answer

I have a 2006 GSI 2.0 Turbo with xenon lights. The lights only switch on after switching the light switch on & off several times. Once the light remain on they work fine until you start the engine. After a...


Could be two easy things, voltage drop from engine starting, alternator has a blown diode so is only supplying DC on and off as it rotates a cycle, or possibly switching to high beam but problems with relay performance/wiring. That latter reason happens on vehicles that has been used as police cars.

Oct 04, 2013 | Cars & Trucks

1 Answer

2004 mazda 6 low beams don't work but high beams do


its probably the switch inside on the steering column check fuses first

Mar 20, 2013 | Cars & Trucks

1 Answer

Low beam dont work


usually both lights don't go at once so it is probably the resistor on the same circuit, probably just a fuse or relay! get a wiring diagram for illumination and test the circuit with a DVOM, bet you just have a bad connection, or loose wire, bad relay.....

Nov 29, 2011 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Only the drivers side headlight works in high beam on my 96 honda oddessey.both the headlights don't work in low beam.what seems to be the problem??


Hello! Replace the Low Beam Cut Relay; It is causing the fault...It is located above the gas pedal...See picture below...Guru...Saailer...


10_6_2011_10_33_43_pm.jpgORIGINAL ENGINE MANAGEMENT Part # DR1067 Cost $10

Oct 06, 2011 | Cars & Trucks

1 Answer

My headlights don't work, but the brights do. What caused this and how can I fix it?


Every headlamp has a bulb inside that has two filaments one for high beam and the other one for low beam, if any of those filament is cut then that beam (High or low) won't work. If your high beam work then your fuse it's ok, so you can visually inspect your headlights bulbs for broken filaments. remove bulb socket and remove the bulb carefully to inspect the filaments. if the filaments are atacched from one terminal to the other then the bulb it's ok, if not replace the bulb.

Jun 28, 2011 | 2002 Chevrolet Suburban

2 Answers

One high beam won't work.


There should be black split tubeing from the head light. Untape and check the connections that have been spliced. Usually the police flasher was hooked up at that point. You may have to follow the wires back to find the break.

Jun 18, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

270 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5581 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...