Question about Ford F-150

1 Answer

I need to find a drigram for a 1995 F-150 XLT transmission? a pattern for pan & bolt speck and lighitng sence? information about toruge.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 71 Answers

They sell Chiltons Manuals at most major parts stores, they will give you the info you need.

Posted on Jul 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have fluid leaking from the bottom of the transmission. Could it be a seal, gasket or do I have to replace the transmission?


What vehicle?
What leaks?

There is no reason to replace anything but the
pan gasket or side case drive axle seals, if you have a front
wheel drive transaxle

You have to get under these vehicles & provide
some info.

They should call this site the Guessing Game Place

Aug 28, 2013 | Cars & Trucks

1 Answer

Replace automatic transmission filter


What is the year/make/model of car/truck in question? Typically it's the same for all cars.
1. Place a large enough drain pan under the transmission.
2. Remove the bolts from the transmission pan in a star pattern leaving a few loose ones at each corner to prevent the pan from dropping.
3. Tap the pan on the side lightly with a rubber mallet to to pop it loose from the hardened gasket.
4. Remove the remaining pan bolts.
5. Remove the one bolt holding the transmission filter in place.
6. Pull the filter off and replace the filter making sure to seat the filter stem back into the transmission; and replace the filter bolt.
7. Clean the pan out with brake parts cleaner, the gasket surface on the transmission, and the pan.
8. Replace the gasket on the pan, and re-install the pan tightening in a star pattern. Use a torque wrench and tighten the bolts to the specified amount in the shop manual. (Typically about 12ft lbs which is just a bit more than hand tight.)


Video Tutorial: http://www.youtube.com/watch?v=lYv58W3kU4I

Nov 24, 2012 | Cars & Trucks

1 Answer

How do I change transmition filter


Start the engine and let it idle for four minutes. This will help to remove as much loose particles from the transmission as possible Turn off the engine. Raise the front of the vehicle using a floor jack, and support the vehicle with two jack stands Apply the emergency brakes and block the rear wheels with two wooden blocks .Place a large drain pan underneath the transmission pan. Loosen the front and side mounting bolts from the transmission pan using a crisscross pattern. Then remove the bolts. Use a ratchet, ratchet extension and socket.Loosen the rear mounting bolts from the transmission pan about 4 turns each. Pry the transmission pan open at the front using a screwdriver and let the oil drain onto the drain pan. Hold the transmission pan from underneath, using a shop rag as you remove the remaining pan mounting bolts. Separate the transmission pan from the transmission, and tilt it over the drain pan to remove the remaining oil. Discard the transmission pan gasket. This is were the filter will be located remove and replace filter and then. Clean the transmission pan with spray carburetor cleaner and a shop rag.Install a new gasket over the transmission pan flange Set the transmission pan in place and start the pan mounting bolts by hand. Start tightening the transmission pan bolts in a crisscross pattern, a little at a time, until all the bolts are tight. Use the ratchet, ratchet extension and socket. Just tighten the bolts enough to create a seal between the pan and the transmission to avoid damaging the pan gasket.

Mar 18, 2011 | 2003 Chevrolet Impala

2 Answers

Leaks transmission oil f


Check transmission pan & lines 4 leak. Tighten all pan bolts, line connectors & drain plug. U may need a new transmission pan gasket. Any cracks in transmission?

Jan 05, 2011 | Nissan Maxima Cars & Trucks

2 Answers

How do you go about changing the trans fluid on a 2005 chevy impala


First make sure you have the proper amount of Transmission fluid to replace what you drain as well as a new transmission filter and gasket. (they usually come in a kit together. The filter & gasket). Make sure the transmission fluid is warm before using jack stands, drive on ramps or a floor jack with jack stands. If there's a transmission drain plug, open it and allow the transmission fluid to drain into a catch pan. If there's not a drain plug, remove the transmission pan bolts, leaving the 4 corner bolts in place until the end. Then slowly loosen two of the bolts at the same end to allow the transmission pan to tilt as well as drain the fluid that way. As the transmission fluid drains, start removing the other two pan bolts to allow more of a tilt until you can place your hand on the pan and remove the remaining bolts, thus removing the pan to be cleaned out. You will normally find a magnet in the bottom of the pan which needs to be cleaned and re-installed. The transmission filter is attached to the "valve body" ,m and when removing that, be aware that more transmission fluid will drain out. To clean a transmission pan, I use either CRC Brake-Kleen or gasoline. Remove all of the pan gasket, install the new filter and replace the transmission pan...don't forget to place the magnet in it and pull your transmission dipstick out of the tube. It has a "vent to atmosphere" so the Brake-Kleen is wonderful for that. If not cleaned, it allows internal pressures to build up inside of the transmission and you could blow transmission seals. Refill with fluid and with your foot on the brake, start it up and allow it to go into ALL the gear ranges, eg. Park, Reverse, Neutral, Drive 2nd and low and then back up to allow the valve body to replace the fluid lost when the filter was changed. Road test and re-check the Transmission fluid Hot on a level surface and add as needed.
A Haynes Manual for your particular vehicle would help with the amount of fluid you will need as well as the tightening pattern of the pan. It also has pictures of what you're going to see before you launch into this task.

Hope this Helps,

"00 Buck"

Jul 12, 2010 | Cars & Trucks

1 Answer

00' Kia Sephia LS not shifting past 1st gear


first you need to buy transmission fluid new filter and new gasket.you need 11.4 pints of transmision fluid.raise front of vechicle.set parking brake.block both back wheels.besure support vechicle weight with jack stands. get a drain pan.if your transmission pan dont have a drain plug.loosen rear pan bolts a few turns.remove the front and side transmission pan bolts. let fluid drain.remove tranny pan. then clean old gasket material from transmission and pan carefully.dont scratch or damage surface.clean old tranny bolts using brake cleaner or buy new tranny bolts.you have to put a tiny film of rtv silicone on tranny bolts so they wont leak.carefully remove old tranny filter and put on new filter.clean all grease grim away from tranny pan it should be **** and span because.you might need a little gasket adhesive to hold gasket in place while putting pan back on transmission.to line up bolt holes.loosely put all bolts in you have to move pan a little to get holes line up.when all is finish put tranny fluid back in.besure you put 11.4 pints back in that about 6.5 quarts. make sure tranny fluid level is right before driving vechicle.l

Jun 19, 2009 | 2000 Kia Sephia

2 Answers

Will a 2001 E4OD transmission fit my 96 F150


I would say that physically the transmission may fit due to the engine sizes being the same, but the 96 F150 is a E4OD transmission and the 01 is a 4R70W transmission, they do not work the same electrically.

May 12, 2009 | 1996 Ford F150 Regular Cab

2 Answers

94 Jeep Grand Cherokee Transmission Problom


1994 is the same as 1997. parts are interchangeable

Dec 31, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...