Question about 1994 Mazda 323

1 Answer

How do i install front wheel bearings on my 1994 mazda 323

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 193 Answers

They are pressed in. It might be easyer to buy spendal assembly if you doing it in the drive way.Need a press to push them out and back in with the new.

Posted on Jul 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power


take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

Tip

Mazda 323/Protege front wheel bearing


The moment you can hear a loud noise coming from front wheels while driving straight that means that your wheel bearings are ready for replacement. In a Mazda 323 BJ (1999-2004) it usually comes every 150-200 thousand kilometers (95-120k miles). To replace the bearing (do two of them in one go even if only one can be heard) you need to do as follows:
Loosen the nut on the half shaft, jack up the car, remove the wheel, dismantle brake caliper and brake disc, remove all ball joints attached to the hub, detach the shock absorber from the hub (no need of removing it completely), once you have the hub basically hanging on the half shaft, untie the nut and pull the hub out of the shaft so you can hold it in your hands. You will need to go to a garage with a 12ton (minimum) press, no point of trying to hammer the bearing out as you may damage the hub and your whole work will be for nothing. Get the old bearing pressed out and the new one pressed in.The Mazda part numbers for the front bearing kit are: B455-33-047A(B,D),GJ21-33-042B,G304-33-065,B21M-33-048.
After getting the bearing fitted into the hub, all we need is to reverse the whole process, put the shaft into the hub, attached the hub to the shock absorber (makes it easier to attach the rest), put the nut and tight it just as much to feel there is nearly no movement (do not overtight it as this might damage the bearing), attach all ball joints back to the hub. Make sure all nuts are tight, use a
tension wrench when needed, put the brake disc back on the hub, install the brake caliper, once you have all them on and tight put on the wheel, then get someone to press the brake while you tight the shaft nut with the tension wrench, check the wheel for play or hard movement. Lower the car down and take a slow drive around (do not accelerate sharply or brake rapidly, just a gentle drive around. Normally a wheel bearing should be in correct position and use after about 200km (120 miles) distance. After that check if it is not overheating (too tight) or there is a play (too loose). Tight or untight if necessary, recheck after same 200km (120 miles).

on Apr 24, 2010 | Mazda 323 Cars & Trucks

1 Answer

Mazda 323 timing marks


well, I hate to tell you, but they never made such a beast. 1994 Mazda 323 , with a 2.0 lt engine, and also no v6 was ever installed in a 323, now if you have the original engine that will be a 4 cylinder 1.6 liter timing mark on the crank and cam is at 12 o'clok., the cam says up, and you line up the mark at 3 o'clock, to the block, i hope you changed the water pump, coolant and rolers ?

Nov 09, 2013 | Cars & Trucks

1 Answer

Front wheel bearing torque specs on a mazda 323


Call your local dealer PARTS department - they have the spec's in their computer system..
Best regards
Ck

Jul 17, 2012 | 1988 Mazda 323 Hatchback

1 Answer

Mazda 323 how I get the hub of on the front wheel to change the bearing. Warming up to get it of ???


Let's make sure you got the correct wheel bearings.

1.57 in. bore;
2.91 in. outer diameter;
1.57 in. width;

These bearings require a 2 ton press and the correct size die to remove and install.

Some shop can do the job for $20 a pair.

Sep 05, 2011 | 2001 Mazda Protege

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

Where is front suspension balljoint replaced on Mazda 323


The front suspension on this car should have struts, which means it will have two ball joints, one on each side. They are in the lower control arm, they connect the front bearing spindle to the lower control arm. They can be difficult to replace, some are bolted and some are press fitted. Any reputable front end alignment shop can replace these, but the cost for doing the job will be more expensive for the press fit ball joints. Hope this helps, let me know.

Dec 15, 2009 | 1994 Mazda 323

1 Answer

Mazda demio airbag light flashing 2 x slow 6 xfast believe this is code 26 what does this signify and how can we recode please. the car is 2003 1,5 gsi uk spec


Hi
Code 26 is the clockspring under the centre of the steering wheel, you may have problems with your cruise control and horn as well. It will most prob need replacing, could be a diy job but bear in mind the previous threads caution.

Oct 30, 2009 | 1994 Mazda 323

1 Answer

Knocking sound when driving over bumps on right hand front side. checked everything underneath, but can find the problem. It's a 1999 Mazda 323 Astina. I'm in Australia by the way. Thanks, Brian :)


did you check our ball joints? jack up the wheel and try to move it side to side and up and down. it should move no more than an 1/8" either way. Any more than that and your ball joints aer starting to wear.

Jun 29, 2009 | 1994 Mazda 323

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...