Question about 1999 Mitsubishi Galant

1 Answer

Trying to remove the Starter

Can't seem to remove the starter.. I removed the Heat Guard and the bolt on the starter and the 2 bolts below starter but it's not budging!! what do you recommend? is there a diagram I can see to know that I'm removing the correct bolts!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 721 Answers

Well before you wind up dropping the trans,lol, check the front side of the trans in front of the starter. There's usually a bolt or or nut on a stud. There's only 3 bolts or 2 bolt & that stud holding it in. Check autozone's site for a diagram or buy a Hayne's manual from any parts store.

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace starter


William,
Remove the following parts to make room and take out starter
through the clearance between body and frame.
' Image
1.Remove FR R.H splash guard.
2.Remove oil pressure switch connector.
3.Remove oil filter.
4.Remove exhaust manifold heat insulater.
5.Remove fuel tube retainer bolt.

25312103-mkm0xbqveb5zta3uncrswycs-4-0.png Auto Repair Help US

Dec 08, 2014 | 1995 Nissan Pathfinder

1 Answer

How to install a starter on a 1999 Mitsubishi Galant?


Welcome to Fixya

Please see procedure below for removal and installation of the starter:

Disconnect the battery, and make sure the engine is cold when doing this because you will be working underneath the exhaust pipes. Using 8mm socket remove the bolts holding the small guard separating the starter from the exhaust. Using a 12mm socket remove the nut on the front (closest to you) part of the cylinoid on top of the starter. Using 14mm socket remove the two bolts holding the starter on to the engine. Take the old starter off, then place the new starter on and following these instructions in reverse order.

Thank you for using Fixya!

Mar 26, 2011 | Mitsubishi Galant Cars & Trucks

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

How do replace the starter on a 1991 mazda protege


Can't remember the particular model 1998, but generally, here's how to remove the starter on a 90's Protege:
Disconnect the negative battery terminal to remove power from the starter. The starter and starter solenoid are one unit.
There should be 2 or 3 14mm bolts holding the starter to the tranny. At least one of these bolts is accessed from above the transmission, requiring the removal of (at least)the air filter housing and intake, and the battery and tray if you want to make it easy on yourself. Remove those first, then remove the top starter bolt before you go under the car. You might be able to access the top bolt from the left wheel well if you take out the plastic splash guard behind the left wheel, and have a nice long extension with a "wobbly" 14mm socket. There are a number of 10mm bolts and a few plastic fasteners that hold this on.
I believe the starter is located behind a bracket that supports the intake manifold from the engiine block. Remove the 4 bolts on this bracket and remove it from the vehicle. The starter wire may be attached to this bracket with a plastic clip, just undo the clip and the bracket should come right out. The bolts that hold the bracket on the manifold end are usually pretty hard to get to; be patient.
Once you have access to the starter, there should be either 1 or two bolts that hold the starter in on the bottom. Remove the bolts and carefully remove the starter from it's position in the transmission. Once you have the starter free, remove the starter cable and the small wire from the clip on the starter solenoid.
Re-install in reverse order.

Oct 09, 2009 | 1991 Mazda Protege

1 Answer

Locating and replacing starter


Disconnect the negative battery terminal to remove power from the starter. The starter and starter solenoid are one unit.
There should be 2 or 3 14mm bolts holding the starter to the tranny. At least one of these bolts is accessed from above the transmission, requiring the removal of (at least)the air filter housing and intake, and the battery and tray if you want to make it easy on yourself. Remove those first, then remove the top starter bolt before you go under the car. You might be able to access the top bolt from the left wheel well if you take out the plastic splash guard behind the left wheel, and have a nice long extension with a "wobbly" 14mm socket. There are a number of 10mm bolts and a few plastic fasteners that hold this on.
I believe the starter is located behind a bracket that supports the intake manifold from the engiine block. Remove the 4 bolts on this bracket and remove it from the vehicle. The starter wire may be attached to this bracket with a plastic clip, just undo the clip and the bracket should come right out. The bolts that hold the bracket on the manifold end are usually pretty hard to get to; be patient.
Once you have access to the starter, there should be either 1 or two bolts that hold the starter in on the bottom. Remove the bolts and carefully remove the starter from it's position in the transmission. Once you have the starter free, remove the starter cable and the small wire from the clip on the starter solenoid.
Re-install in reverse order.

Thanks
Kindly rate the answer
Smith

Jul 09, 2009 | 1993 Mazda 929

1 Answer

96 starter replacment


1st disconnect the battery there a few bolt that hold the plash guard after remove the 2 bolt holding the starter after the starter loose remove the big bolt that hold the batterycable and after the little on remove starter and reinstall good luck pierre

Mar 03, 2009 | 1996 Chevrolet Monte Carlo

2 Answers

Can't find the starter in a dodge spirit 1989


Taken from Haynes repair manual. I used these instructions myself to replace starter motor on my 1989 Dodge Spirit after nearly going berserk at three attempts to remove it without wanting to look it up in book.
1)Detach the negative battery terminal. 2) Working from above the engine, remove upper mounting bolt and nut to starter. (Access is accomplished this way: stand on driver-side fender and look down at brake fluid reservoir. Just below and beyond the brake reservoir you will see a vent hose. Disconnect hose & remove. Now you will see the starter motor from above view. You will be able to see a mounting bolt and a nut connecting starter to engine just above the starter (facing brake reservoir). Remove (1) bolt & (1) nut first, then raise vehicle and suport on jackstands. Then go underneath the vehicle and remove the remaining lower mounting bolt (1) on the starter. Label wires then detach them from starter. Now you can remove the starter. If you find it a tight squeeze, you may want to remove or swing the transaxle on that side for additional access, although that is not mentioned in manual (but I did it). It just gives you more room, but does not seem absolutely necessary. 3) Installation is reverse of removal.
please do rate the solution.
thank you for using fixya.

Feb 09, 2009 | 1989 Dodge Spirit

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

1 Answer

How do I replace the starter?


  1. Remove FR R.H splash guard.
  2. Remove oil pressure switch connector.
  3. Remove oil filter.
  4. Remove exhaust manifold heat insulater.
  5. Remove fuel tube retainer bolt.
only 4wd

  1. Remove FR R.H wheel.
  2. Remove FR R.H splash guard.
  3. Remove exhaust manifold heat insulater.
  4. Remove exhaust manifold.
  5. Remove oil filter.
  6. Remove oil pressure switch connector.
other but 4wd

May 15, 2008 | 1995 Nissan Pathfinder

Not finding what you are looking for?
1999 Mitsubishi Galant Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...