Question about 1997 Infiniti.5 Q45

1 Answer

WHEN REPLACE FUSE FOR POWER SEAT, ENGINE START SHAKING, PLEASE ADVISE ON WHAT TO DO

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Seat probably draws too much current, overworking the alternator, putting more load on the engine. or the battery might be poor.

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chevy equinox license plate light won't work after bulb and fuse replacement


Do the park lamps work ? license plate lights get power from same fuse ! Check ground wire ! use a volt meter an do voltage drop test ! Voltage Drop Testing The fuse for the license plate lights is in the under hood fuse box -engine compartment ! fuse #12 RT PRK LAMP 10Amp .

May 23, 2015 | 2007 Chevrolet Chevrolet Equinox LT

2 Answers

Ford f150 driver side power seat mirrors heated seat and 4 wheel drive not working


This is a very common failure, depending on the year of your truck. Check the fuse panel under the hood VERY CLOSELY and make sure there is no corrosion AT ALL, and that each and every fuse/relay is seated nice and tight and in the correct spot. Pay close attention to fuse #23 and the surrounding areas as that is usually part of the problem. Further more, the wiring up to this panel needs to be traced back, and i believe that there's a loom that goes through the firewall and can be exposed/rubbed/chaffed/ in the driver side wheel well, especially if there is aftermarket or bigger wheels installed. finally, any malfunction indicator lights? any fault codes? how long has this been happening? and has it continued to get worse. Please Advise, we are here to help.
Regards,
-Tim

Jan 06, 2015 | Ford Cars & Trucks

2 Answers

Can't get the drivers seat to move, could it be a fuse and where would that fuse be located?


Fuses are located on the drivers door jamb and in the engine compartment. See your manual. If the passenger seat is power and it works, then your problem is not a fuse but a switch.

Mar 21, 2014 | Oldsmobile Aurora Cars & Trucks

1 Answer

Fuel pump relay


CHECK FUEL PUMP FUSE FIRST /THEN START BY HAVING SOMEONE UNDERNEATH THE CAR BY GAS TANK /SOMEONE ELSE START OR CRANK ENGINE 4 ONE SECOND LEAVE IGNITION ON THEY SHOULD HEAR PUMP RUNNING IF NOT LOCATE WIRES GOIING INTO FUEL PUMP/UNDERNEATH CAR BY GAS TANK OR UNDER BACK SEAT?CHECK WITH TEST LIGHT 4 POWER/NO POWER REPLACE PUMP.HAVE A NICE DAY

Jun 01, 2013 | 1996 Toyota Corolla

1 Answer

Efi fuse blown after engine start


I think gas is not getting to your fuel rail.

Could be the fuel pump. To access it you will have to remove you rear seat and take off an oval shaped plate. There you can remove it and replace the pump.

May 24, 2010 | 1990 Toyota 4Runner

1 Answer

1998 plymouth engine fuse burns


first place i would start looking is the wiring to the O2 Sensors for shorts to ground or
in case the O2 Sensor itself is shorted, try disconnecting the sensors to see if the fuse stops blowing.
this is just a place to start, there are other problems that will blow that fuse. good luck.

Jun 17, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Engine shaking


Its the crankshaft sensor. this sensor, when bad, will send mixed signals to the engine CPU that will through of timing dramatically. replace the sensor asap.

May 22, 2009 | 1998 BMW M3

1 Answer

No main engine fuse, fuse pump fuse


this model dont have fuel pump fuse , the ecm supply power to pump, check EFI fuse 15amp , if good, then remove rear passenger seat, to check the fuel pump , give me for notice please

May 03, 2009 | Lexus ES 300 Cars & Trucks

3 Answers

2001 Chevrolet Tahoe - Power seat


The most likely cause is the switch, replace it.

Sep 22, 2008 | 2001 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14338 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...