Question about 1999 Chrysler Sebring

1 Answer

Have a 99 sebring just changed battery and car wonk crank

Have a 99 sebring just changed battery and when you turn the key car doesnt crank but all the idiot lights go on so its not the battery what else could be the problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 431 Answers

Hi I am Vortash when you turn the key is there a sound from the engine a clicking noise this would be the pre engaged starter motor solenoid trying to engage if you do then the starter motor may be jammed or faulty or possibly has a bad earth check all your body earthing straps .. ( the lights would work as they dont take much drain but the amperage of the starter motor wouldnt ) .
If after checking the earths you dont hear this then I would suspect that the ignition switch is at fault and the starter motor contacts in the switch have burned out or the starter relay hope this is of help regards vortash

Posted on Jul 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 96 sebring coupe xli wont crank or start how do i check the starter relay


Is the transmission (automatic assumed) in "P"? If manual, are you holding the clutch pedal down?

Do you have functioning headlights? Does the starter TRY to crank the engine but not have enough power to do it? If so, check all your ground connections. Is the battery discharged or fully charged?

Put a voltmeter on the battery and have someone try to start the car. Watch the battery voltage when they turn the key - it should NOT drop below 9V. If it does, it's discharged or internally damaged.

It may be a pure coincidence - all batteries get to a certain point after which they can't be used any more. You may have just lost one cell in the battery. Or... when you changed the water pump, you may have disturbed something you shouldn't have disturbed.

Jul 29, 2014 | 1996 Chrysler Sebring

1 Answer

Po725 code on chrysler sebring can it cause the starter to go bad


Hi there:

DTC P0725 - ENGINE SPEED SENSOR CIRCUIT


When Monitored: Continuously after a ignition key is turned from the OFF to RUN

position and/or key is turned from the CRANK to the RUN position.

Set Condition: The code is set when the engine speed sensed by the Transmission Control

Module (TCM) is different than the engine speed reported by the Powertrain Control

Module (PCM) over the Communication Buss.


POSSIBLE CAUSES:

CHECKING SYMPTOMS AND POSSIBLE CAUSES

LOW BATTERY VOLTAGE

BAD CONNECTIONS AT VARIOUS CONNECTORS

CRANK POSITION SENSOR SIGNAL OPEN

CRANKSHAFT POSITION SENSOR GROUND CIRCUIT OPEN

TCM CRANK POSITION SENSOR MONITORING DEFECTIVE



Hope this helps.

Mar 30, 2012 | 2001 Chrysler Sebring

1 Answer

I have a 04 chrysler sebring and the speedometer spiked all the way to the other side after the battery was changed. How do I get it back to normal?


try setting the odometer to read the trip miles. Then turn the ignition key to the off position. Now while holding the trip meter reset button in, turn the ignition key to the run position ( not cranking the engine just until the dash lights come on). The dash should go into a reset mode. You can release the trip reset button while the dash resets itself, should take less than a minute to complete.

Sep 19, 2011 | 2004 Chrysler Sebring

3 Answers

Key won't turn in my ignition on 99 sebring


have you tried jiggling the steering wheel back and forth while you turn the key.

Feb 06, 2011 | 1999 Chrysler Sebring

1 Answer

Wen trying to crank wont start just spin over and


at the top of the clutch pedal is a switch that has to be replaced or you can hook the two wires together. this may be problem.

Apr 04, 2010 | 1996 Chrysler Sebring

1 Answer

Will not start, will only turn over. battery is good.


Are you getting spark.If not replace the crank sensor first then try.If still no spark change the coil pack.That should solve your problem.Let me now if it doesnt.

Dec 27, 2009 | 1999 Chrysler Sebring

2 Answers

My 2001 sebring won't start. with the key in the


if your battery has power [ check head lights work] its probably the fusable link

Jul 17, 2009 | 2001 Chrysler Voyager

1 Answer

I need to put the altinatior back in


Make sure your car is not in a year change. If so you could require parts from a early model or later model.

Apr 09, 2009 | 1999 Chrysler Sebring

1 Answer

2001 sebring 4 door 2.7


It could be the neutral safety switch if it is an automatic transmission car. If it is a manual transmission car their is a safety switch in the clutch pedal. If these check out ok then check the starter solenoid

Jul 08, 2008 | 2001 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Sebring Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...