Question about Chevrolet Tahoe

1 Answer

'95 tahoe making noise when accelerating; sounds

'95 tahoe making noise when accelerating in 2wd; sounds like 4wd is trying to engage, kind of a grinding noise. Question; should front drive shaft spin also even when in 2wd? Put rearend up on jack stands and put in drive, hit the gas and drive shaft for front end spins also but not all the time, sounds like transfer case but not 100% sure.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 199 Answers

No it should not spin when is in 2wd thanks

Posted on Jul 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Tahoe 4wd isn't engaging in 1,2,or 3rd or drive. It only goes forward when the gear shift is on reverse and when it starts to move it makes a loud clunk noise and grinding.


Not sounding to good. Sounds like you wiped out the planetary gears. Depending on the damage, your looking at $2000 rebuild.

Feb 07, 2016 | 2001 Chevrolet Tahoe

1 Answer

2005 Suburban Front End Noise


check for hangings anything hanging may rub on other items and make a noise... you may have bent a rod for the drive section or cracked the case...look for fluid leaking

Mar 05, 2013 | 2005 Chevrolet Suburban

1 Answer

Hi I am having the same problem as tjtwo1965 posted with my 96 Tahoe, been suggested that worn selector fork is trying to engage 4wd while in 2wd, but then also reading about these snap rings breaking....


Sometimes the front end alignment can affect how the car shifts in and out of 4 wheel drive... are your front end parts worn out? (usually happens with worn out ball joints) I got mine out by compleatly lifting the front tires off the ground and shaking the front wheel while a friend worked the geers (foot on brake, lever in nuteral, make sure your on level sturdy ground)

Mar 18, 2010 | 1996 Chevrolet Tahoe

1 Answer

Transfer case fuse blows when engaging four wheel drive.


Hello;
Sounds like yoou have a short either in the switch pod or in the 4wd electrics. Check for pinched wires or bare wires grounding out at the front axle and at the transfer case.
Thanks;
Rich
RPM Northwest

Jan 20, 2009 | 1996 Chevrolet Tahoe

1 Answer

03 Chevy Tahoe Z71 - 4wd not functioning


my son has one and his did that and it was a fuse he put a new one in and it is working good now

Jan 14, 2009 | 1999 Chevrolet Blazer

1 Answer

95 jeep grand cherokee won't go back into 2wd.


Stick it in 2wd. Now back it up a good bit. Now pull it forward. Now make a turn. If it lurches, then repeat.

After this, check your tires. If the tires are different sizes. or the front is worn more than the rear, or even if they're different manufacturers, or if the tire pressure is low, then these could all be reasons that the transfer case is getting confused and is finding it hard to come out of 4wd.

This is assuming that the transfer case is in good working order and has the correct amount and type of fluid in it.

Jan 12, 2009 | 1993 Jeep Grand Cherokee

2 Answers

91 Jeep Wrangler Sahara, 2WD won't engage, 4WD is fine!


It sounds like your driveline to the rear wheels is broken. Could be transfer case output shaft to the rear wheels has broken. Try disconnecting the rear drive shaft and see if you can turn it by hand with the transfer case engaged in 2WD. If you can turn it while the Sahara is in gear, the output shaft is no longer connected to the engine for some reason.

Dec 29, 2008 | 1991 Jeep Wrangler

2 Answers

94 4Runner 4WD Question


1. I would suggest that you engage your 4WD while you are in full stop and/or safe range of 5mph, however as claimed by the local dealers your vehicle is capable of engaging even while driving. Engage your 4WD while moving only when necessity requires.
2. That clicking noise while turning extreme right or left would be the birfield of your axle and would only mean your front hub is still engage even though you have disengaged transfer case.
Have your front hubs cleaned of old lubricants or grease due to non usage. dont use grease as lubricants, use thick oil such as gear oil or silicone oil. and use your 4WD every now and then.

Do this first then check if you still feel somtehing is loose on your suspension and others.

Dec 10, 2008 | 1994 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

992 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...