Question about 2000 Chevrolet Silverado 1500

1 Answer

Installed new radio, now radio works but no instrument panel lights. Turn siginal, shift light, 4x4 light and all other work, just no gauge lights. I did notice a dimmer positive wire that was not used when installing the new radio and wondered if that was the cause.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 43 Answers

I would try jumping power to that wire and see if they turn on. That is most likely the problem. I would just jumper it to a power source again after in the same manner that is was before.

Posted on Jul 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No dash lights when headlights are turned on. Everything works fine on my vehicle EXCEPT today the panel lights don't work. Turn signals, hazard blinker, oil gauge, rpm gauge, speedometer, drive shift...


there is a regulator for the display brightness, you may have it turn'd down or it has stopped working;. it controls the brightness at which the dash lights are. usually has a speedo sign on it. goes up and down. it works with the main light and is conecter to them on the same lighting board if it has gone then a new light swtch control switch will be needed.

Oct 13, 2013 | 2001 Chrysler Town & Country

1 Answer

Tranmission and instrument cluster


The speed sensor on your trans sends a signal to the electronics telling it when to shift, this will be where you fault is.

Mar 05, 2012 | 2001 GMC Yukon XL

1 Answer

1998 instrument panel lights dont work after


CHECK THE CLUSTER ELECTRICAL WIRES.COULD HAVE KNOCK THEM LOOSE WHILE REMOVING THE RADIO.

Apr 25, 2010 | 1998 Oldsmobile Cutlass

1 Answer

My 2003 F-150 will not engage the 4-wheel drive when the switch is turned on? Two days ago it worked fine and the light does come on?


Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
If it turns it is a problem with the transfer case.
If it doesn't it is a front axle engagement problem.

I am going to guess the drive shaft will not turn, and the problem is the shift disconnect motor on the front axle, or the shift solenoids.
The shift motor looks like this
37bcd6a.jpg

The shift solenoids look like this :
1a11fc1.jpg

You can check the shift solenoids with a vacuum gauge. The blue vacuum line is the 4WD operation, the pink is the 2WD operation. Pull the vacuum line at the shift disconnect motor, and install the vacuum gauge. Shift into 4WD and the vacuum should be on the line, and hold. If not could be the disconnect motor or the vacuum line to the motor.

Could also be the shift motor in the transfer case, but with the 4x4 light on the cluster lighting up, the transfer case should have shifted, the confirm comes from the transfer case to illuminate the 4x4 indicator on the cluster.

Feb 20, 2010 | 2003 Ford F150 Regular Cab

1 Answer

I have a 1997 Jeep Cherokee. My issue is with the interior instrument lights, none of them work. I checked ALL fuses inside and out of the vehicle and all tested GOOD. Guages work and Radio display works...


It is the headlight switch, very common problem on jeeps, my 96 grand cherokee dose the same but most times the lights will flicker. Try spraying a small amount of WD-40 in to the panel dimmer switch and then move it around and kind of jiggle it around.

Feb 05, 2010 | 1997 Jeep Cherokee

1 Answer

Does 2001 Jeep Cherokee Sport 4x4 have a lighted


The instrument panel shows a message "part time" when you shift to 4wd hi

Jan 09, 2010 | 2001 Jeep Cherokee

1 Answer

Instrument panel lights will not work after new battery was installed. Previously, When door was opened one could hear static noise and flickering of instrument panel lights. Battery was checked and was no...


Hi 1987 Honda Civic lihgts on instrument panel. New Battery. and replaced blower unit but lights on panel not working. I am yet to install stereo unit which was taken out by previous owner - very roughly ! Wondering if not having stereo will effect instrument panel lights. Cheers Steve

Nov 22, 2009 | Chevrolet Impala Cars & Trucks

4 Answers

Instrument panel went dead


Checked Every fuse in the fuse box (no small task).This includes #4 - Power point Instrument Panel, #14 - Day time running lamps (auto lamps doesn't work nor does auto lock), #27 - ignition switch run feed, #35 - Instrument Cluster, #41 - Instrument Cluster, #42 - Delayed Accessory, #45 - Ignition switch run/start feed, #102 - Door locks body security module, #103 - Ignition switch, #110 - Ignition switch, & #116 - Ignition switch. But I also check all other ones as well, they all register OK. AC panel & radio work. Turn signals work. Mileage does not work, trip computer does. So, basically, everything works except auto head-lights, auto locks, and the dash cluster (no MPH, RPM, mileage display, Fuel, Temp, Tran Temp, and Oil Pressure).

Aug 19, 2009 | 2003 Ford Excursion

1 Answer

Gas gauge no longer works


The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

May 14, 2008 | 2007 Jeep Scout

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...