Replaced water pump on 96 toyota corolla 1.6 and pinched crankshaft position wire now engine won't start. possible solutions?

Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...

P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota

31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html

toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair

Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Remove the distributor cap and check for water inside it. Ignition wires may have gotten wet as well and possibly need to be replaced

1996-1999 Toyota Corolla valve timing:
It is very easy to install the timing belt on 1997 Toyota Corolla. Do the following:
- Mark the numbers 1,2 and 3 on the spark plug wires with permanent marker or nail polish and remain the 4th one unmarked. This is necessary so that you can easily remember the spark plug wires order later on their original position.
- Remove the spark plugs so that the engine can easily be rotated.
- Rotate the crankshaft clockwise to align the v- groove mark on the crankshaft pulley with the 0 mark on the timing belt cover. If these marks are aligned the piston is always on the Top Dead Position (TDC).


- To replace the timing belt remove the crankshaft pulley, upper and lower timing covers.
- Temporarily screw in the crankshaft bolt in its place to rotate the crankshaft with the spanner and align the v- groove of lower crankshaft gear with the index mark on the oil pump cover as shown in the following diagram.
- Inspect the cam shaft mark through the small hole on the cam shaft sprocket. The punch mark should be exactly behind the hole on the cam shaft sprocket as shown in the following diagram.



- Loosen the timing bearing bolt, press the bearing forcefully against the spring with some suitable tool and lock it there temporarily.
- Remove the timing belt.
- Remove the timing bearing.
- Replace the new timing belt and bearing with the original.
- Install in the reverse order of dis-assembly.
NOTE: NEVER PUT EXTRA FORCE ON TIMING BEARING TO ADJUST THE TIMING BELT TENSION. JUST LOOSEN THE TIMING BEARING BOLT AND THE SPRING ATTACHED TO IT WILL PULL THE BEARING IT SELF WITH THE PRESET TENSION TO ADJUST THE TIMING BELT.
Thank you for visiting Fixya.

something heating up try coils or check the crankshaft and camshaft sensors

check your fuel pump you might be losing pressure

Since the water pump is leaking there is low action of the water pump to circulate the water into the engine jackets and the radiator.
So you need to remove and overhaul or replace the water pump, replace the gasket, check the radiator for leaks with high pressure test, replace with a good cap and the fault of heating and steaming will be gone. Also check the timing of the engine, do a tune up.

1.check fuel pressure in fuel line -fuel press





2.check engine compression using compression tester





check this two step maybe get the trouble area

Hi there,

Well if you are not mechanically educated, you should not try this alone. the water pump alone is not the problem, it is the timing belt. mess the timing up, and the engine will not start or if it does start, it will run rough. the water pump runs behind the timing belt, so it must be removed (Possibly replaced) anyway you can please follow the below steps -
1. Disconnect the negative cable on the car battery before you begin.
2. Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
3. Remove the right-hand engine under cover with the drive belt.
4. Loosen and remove the bolts to the water pump and take the water pump out of the engine.
5. Install the new water pump. Tighten the short bolts to 80-inch lbs. (9 Nm) and tighten the long bolts to 96 inch pounds (11 Nm).
(1ZZ-FE Corolla Engine)
6. Reinstall the drive belt and the right engine under cover.
7. Reconnect the negative battery cable.
8. Refill the cooling system with coolant to the proper levels. Start the engine and check for leaks when the engine reaches normal operating temperatures.
Please post comments if you need more help or information........

Good Luck!!

Thanks

Symptoms Symptoms can include:

• Hard starting or no start
• Rough running / misfiring
• Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:

• a wire or connector in the circuit could be grounded/shorted/broken
• the camshaft position sensor may have failed
• the PCM may have failed
• there exists an open circuit
• the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Visually inspect all the wiring and connectors in the circuit
• Check for continuity in the circuit wiring
• Check the operation (voltage) of the camshaft position sensor
• Replace the camshaft position sensor as required
• Check the crankshaft position circuit as well
• Replace circuit wiring and/or connectors as required
• Diagnose/replace the PCM as required

Remove all accessory belts, support engine, undo engine mount, remove timing belt covers, remove timing belt, remove pump.