Question about 2004 Toyota 4Runner

1 Answer

Maintenance light on dash how do you reset it had oil changed but they did not reset the light

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,959 Answers

Courtesy of www.synthetic-direct.ca

  • Turn the ignition key to the OFF position with the odometer reading shown.
  • Turn the ignition key to the ON position while holding down the trip meter reset button.
  • Hold down the button until the light goes off.
  • Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds, and illuminates for 1 second. If the system fails to reset, the light will remain flashing
Hope this answers your question. Best of luck.
Greg

Posted on Jul 22, 2009

  • Greg Margossian
    Greg Margossian Jul 24, 2009

    Kindly rate the solution you've been provided if you feel it answered your question. Thank you very much.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i reset oil change button?2003 model Toyota hillux extra cap


Turn the ignition key to 'ON' and press the odometer button until the display reads ODO (not Trip A or B).
Turn the ignition key to OFF.
Hold in the same button you used in step 1.
While holding the button in, turn the ignition key to ON.
The ODOMETER will change to:
5 dashes - - - - -
Then 4 dashes - - - -
Then 3 dashes - - -
Then 2 dashes - -
Then 1 dash -
THEN all zeros 0 0 0 0 0
Then back to the correct mileage.
Then the Maintenance Required light should blink and go out.

Aug 03, 2016 | Toyota Cars & Trucks

Tip

Ford service light procedure 1994-01


Windstar

1999-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the message center, press the SETUP control to access the System Check mode. Press and release the RESET button until IF NEW OIL HOLD RESET is displayed. Press and hold RESET button until OIL LIFE SET TO 100% is displayed.


Windstar


1997-98

To reset "CHANGE OIL SOON/OIL CHANGE REQUIRED" message on the Message Center, press "RESET" and "SETUP" controls at the same time. "OIL LIFE % HOLD RESET NEW" will be displayed. Press the "SETUP" control to access the System Check mode. Press "RESET" to start the system check. Press and hold the "RESET" control. Press "RESET" and "SETUP" to reset the system to 100%


Explorer,
Mercury
Mountaineer


1997-01

To reset the oil life feature on the Message Center, press and hold the "OIL CHANGE RESET" button until the system counts down (about 5 seconds). The Message Center will display "OIL LIFE RESET TO 100%"


Probe

with Analog Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE INTERVAL CHECK" is displayed is displayed on the far left side of the instrument panel, press the "SERV OFF" button, located on the speed alarm keyboard, until three tones sound.


Thunderbird,
Mercury Cougar

with System Scanner

1986-88

When "SERVICE" appears on the Diagnostic System Scanner, press the "ODO SEL" and "TRIP RESET" buttons simultaneously. The "SERVICE" message will go out and three short beeps will be heard when the system is reset.


Thunderbird,
Mercury Cougar


1989-94

If "CHANGE OIL SOON" or "NOW" is indicated on the Monitor, turn the ignition on, but do not start the engine. Within 16 seconds, insert a paper clip into the cavity to the left of the display and depress. The display will flash; when it stops, the system is reset.















on Dec 07, 2009 | Ford Windstar Cars & Trucks

1 Answer

Main reop light in dash


Hello, and welcome to FixYa.

The 'Maint Reqd' light indicates that you are due for an oil change. It will blink 4,500 miles since the light was reset at your last oil change, and stay on steady after 5,000 miles.

If you recently had an oil change, all you need to do is reset your maintenance reqd lamp. The procedure is here on this site inthe 'tips and tricks' section, and it is also in your owner's manual.

Feb 22, 2010 | 2004 Toyota Camry

3 Answers

The 'Maintenance Required' light flashes on my


this is just your maintence minder. the reset procedure should be in your owners manual. the vehicle calculates when its due for an oil change and turns the light on but it should be reset every oil change if its on or not. you can can your local acura/honda dealer and they can explain how to reset

Nov 02, 2009 | 2001 Acura MDX

2 Answers

Maintenance required is on red what do i check for i changed the oil out new spark plugs


You have to reset it by holding the button on the dash that looks like odometer reset button then turn key on while holding that button that will reset that light.

Sep 04, 2009 | 1993 Honda Accord

4 Answers

Reset maintenance light


If I remember correctly, on the dash you have a select button. Hold the button down then turn the key on, until the maintenance light blinks and goes out. Turn the key off then back on and your light should be out.

May 28, 2009 | 2005 Honda Civic

1 Answer

Oil light comes on after oil change 1992 acura integra.


If the oil lamp itself is illuminating it is not a maintenance light that can be reset the oil pressure sending unit is detecring low oil pressure. You should have the vehicle serviced right away. The reset procedure for the maintenance indicator is as follows,with the key off depress & hold the odometer/trip button on the instrument panel turn key to run position wait 10 seconds for reset

Apr 17, 2009 | 1992 Acura Integra Hatchback

3 Answers

How to reset maintenance display on my 2007 Nissan Altima Hybril


Hi, I'm a DIY guy, but I don't know how to reset the oil maintenance light that came ON on my 2010 Altima. I had it service at the dealer and won't tell me how to reset it. Thanks

Jan 25, 2009 | 2008 Nissan Altima Hybrid

1 Answer

Chevrolet Express 1500 Maintenance 1 & 2


when you do a oil change you need to reset or light will come . to do this you turn on key hit gas pedal 3 times really fast

Oct 19, 2008 | 2007 Chevrolet Express Passenger

Not finding what you are looking for?
2004 Toyota 4Runner Logo

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...